GE lp33 20 series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 43

background image

Critical Power

Modifications reserved

Page 23/43

GE_UPS_ISG_LPS_3UL_20K_30K_2US_V010.docx

Installation Guide

LP33 Series 20 & 30 UL S2

Fig. 4.7.2-1 RPA Parallel System

In order to ensure a correct load sharing between the parallel units, when the

load

is

supplied by

utility

, it is recommended to keep the cable size and length from the input

distribution board to the output bus-bar the same for each parallel unit.

Utility Bypass input voltage

must be the same for all units, thus avoiding phase shift or

phase rotation problems.

To avoid mutual induction effect, the input cables must be run in separate conduit
from the output cables.

NOTE !

No transformers, fuses or automatic circuit breakers should be inserted
between the unit’s output and the load common bus-bars.

The delivery and installation of fuses and input / output connections of the UPS are at the
customer’s expense, unless agreed otherwise

.

NOTE !

It is recommended to provide an additional length of the input/output cables so that
the UPS can be moved for maintenance purpose.
It is recommended to use flexible input/output conductors with suitable length to
admit a sufficient displacement.

4.7.3

Battery over current protection and wire sizing



Please read the safety precautions at the front of this guide carefully, and thoroughly review the
battery manufacturer’s installation and maintenance manual before connecting the batteries to
the UPS.



Choose an appropriate DC fuse or circuit breaker using the current data in the chart below.



Minimum battery cable requirement is based on the current data below.

LPS33U_020-030_RPA system_GE_01US

LOAD

LP33 Series 20 & 30

1

UTILITY INPUT

F1

F2

F3

F4

LP33 Series 20 & 30

2

LP33 Series 20 & 30

3

LP33 Series 20 & 30

4

«
...
21
22
23
24
25
...
»

Содержание lp33 20 series












































Отзывы:

Нет отзывов

Похожие инструкции для lp33 20 series

Бренд: Falcon Страницы: 47

ups302R2002N035

Бренд: Delta Страницы: 4

Бренд: Eaton Страницы: 46

Gamatronic B300

Бренд: SolarEdge Страницы: 101

Бренд: DSPM Страницы: 32

Бренд: Vesta Страницы: 2

Бренд: Coolmax Страницы: 23

Бренд: Fortress Technologies Страницы: 38

Бренд: LEGRAND Страницы: 1398

Бренд: Digitus Страницы: 4

Бренд: SurgeX Страницы: 24

Бренд: Eaton Страницы: 8

Бренд: CyberPower Страницы: 2

Бренд: CyberPower Страницы: 2

Бренд: CyberPower Страницы: 2

Бренд: CyberPower Страницы: 4

Бренд: CyberPower Страницы: 16

Бренд: CyberPower Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды