GE lp33 20 series Скачать руководство пользователя страница 14

Страница: 14 / 43

Critical Power

Modifications reserved

Page 14/43

GE_UPS_ISG_LPS_3UL_20K_30K_2US_V010.docx

Installation Guide

LP33 Series 20 & 30 UL S2

4.2

DELIVERY

When delivered, check carefully the

package integrity

and the

physical conditions of the UPS

equipment

In case of any damage sustained during transport, immediately inform the carrier and contact your

local

Service Center

detailed report

of the damage is necessary for any insurance claim.

NOTE !

A damaged UPS must never be installed or connected to

utility

battery

4.3

STORAGE

The equipment is carefully packed for transport and storage
so that it is in a perfect condition when eventually installed.

Never leave a UPS outside the building and do not store the
UPS one on top of the other.

It is recommended to store the UPS in its original package in a

dry, dust free room and far away from chemical
substances, with temperature not exceeding -13°F

131°F

(-25°C to 55°C).

4.3.1

Storage of the UPS

Some important functions of the UPS, such as the customized functions, are defined by parameters

stored in a

RAM memory

The RAM is supplied by a small

backup battery

located on the

Control Unit board

If the storage time of the UPS exceeds

1 year

these functions

should be verified

by an authorized

Service Center

before putting the UPS into operation.

NOTE !

In case of storage of the UPS pay attention to:

4.3.2

Storage of the battery

In case of extended storage, when the delivery includes maintenance free batteries, keep in mind that

they are subject to auto-discharging process

To avoid permanent damages to the battery, you must observe the following instructions:



The storage time without charging the battery depends on the ambient temperature of the storage area.



The optimal ambient temperature for the batteries is

68°F

(20°C).

For storage temperature higher than

68°F

(20°C), the storage time will decrease.



Each additional

18°F

(10°C) over the nominal temperature of

68°F

(20°C) will decrease the storage

time, without freshening charge, by half.

In case of a

maintenance free battery

, the storage time without charging the

battery

approximately:

6 months with storage temperature 68°F (20°C)
3 months with storage temperature 86°F (30°C)
2 months with storage temperature 95°F (35°C)

NOTE !

In case of

battery

storage pay attention to:

FRAGILE

SENSITIVE

TO DAMPNESS

TO HEAT

SENSITIVE

TO FROST

SENSITIVE

FRAGILE

SENSITIVE

TO DAMPNESS

TO HEAT

SENSITIVE

TO FROST

SENSITIVE

Содержание lp33 20 series












































Результаты поиска

Содержание lp33 20 series

Отзывы:

Похожие инструкции для lp33 20 series

Бренды по названию

Популярные бренды

GE lp33 20 series, Руководство по установке

Результаты поиска

Содержание lp33 20 series

Отзывы:

Похожие инструкции для lp33 20 series

Бренды по названию

Популярные бренды