GE lp33 20 series Скачать руководство пользователя страница 6

Страница: 6 / 43

Critical Power

Modifications reserved

Page 6/43

GE_UPS_ISG_LPS_3UL_20K_30K_2US_V010.docx

Installation Guide

LP33 Series 20 & 30 UL S2

SAFETY RULES

With this document,

gives to the user all the necessary information about the correct use of the UPS.

Please read carefully this

Installation Guide

before installing the UPS.

We recommend that this manual be kept next to the UPS for future references.

If any problems are encountered with the procedures contained in this manual, please contact the

nearest

Service Center

before you proceed.

All UPS installation, maintenance and service work should be performed by QUALIFIED SERVICE
PERSONNEL only.

The KNOWLEDGE and the FULL compliance of the safety instructions and
warnings contained in this manual are

THE ONLY CONDITION

to avoid any dangerous situations during installation, operation,
maintenance work, and to preserve the maximum reliability of the UPS
system.

NOTE !

LP33 Series 20 & 30 is

an FCC Class A-UPS Product.

While every care has been taken to ensure the completeness
and accuracy of this manual,

assumes no responsibility or

liability for any losses or damages resulting from the use of the
information contained in this document.

Refuses any responsibility in case of non-observance,
unauthorized alterations or improper use of the delivered UPS.

Содержание lp33 20 series












































Результаты поиска

Содержание lp33 20 series

Отзывы:

Похожие инструкции для lp33 20 series

Бренды по названию

Популярные бренды

GE lp33 20 series, Руководство по установке

Результаты поиска

Содержание lp33 20 series

Отзывы:

Похожие инструкции для lp33 20 series

Бренды по названию

Популярные бренды