GE lp33 20 series Скачать руководство пользователя страница 3

Страница: 3 / 43

Critical Power

Modifications reserved

Page 3/43

GE_UPS_ISG_LPS_3UL_20K_30K_2US_V010.docx

Installation Guide

LP33 Series 20 & 30 UL S2

Dear Customer

We thank you for selecting our products and are
pleased to count you amongst our very valued

customers at

We trust that the use of the

LP33 Series 20 & 30

Uninterruptible Power Supply system, developed
and produced to the highest standards of
quality, will give you complete satisfaction.

Please read carefully the

Installation Guide

which contains all the necessary information and
describes all you need to know about the
installation of the UPS.

Thank you for choosing

START-UP AND COMMISSIONING

A GE Critical Power Field Services Engineer must perform start-up and
commissioning of the UPS.

Please Contact GE Services at least two weeks prior to schedule start-up and
commissioning at

1-800-637-1738

, or by E-mail at

[email protected]

Distributed in the USA by:

Your service contact:

GE Consumer & Industrial SA

General Electric Company

CH – 6595 Riazzino (Locarno)

Switzerland

www.gecriticalpower.com

GE Energy Connections

Critical Power

3100 Technology – Suite 200

Plano, TX 75074

T: +1 800-637-1738

[email protected]

www.geindustrial.com/products/

critical-power

GE Energy Connections

Critical Power

601 Shiloh Road

Plano, TX 75074

24/7 T: +1 800-637-1738
24/7 F: +1 866-765-3595

[email protected]

Содержание lp33 20 series












































Результаты поиска

Содержание lp33 20 series

Отзывы:

Похожие инструкции для lp33 20 series

Бренды по названию

Популярные бренды

GE lp33 20 series, Руководство по установке

Результаты поиска

Содержание lp33 20 series

Отзывы:

Похожие инструкции для lp33 20 series

Бренды по названию

Популярные бренды