GE EV100 LX Скачать руководство пользователя

Страница: 68 / 81

1234567890

DESCRIPTION AND LOCATION

Z PLUG

Y PLUG

B PLUG

A PLUG

EV100 LX/LXT

FUNCTION SET-UP PROCEDURES:

Warning: Before making any adjustments to the control

you must consult the operating and maintenance instruc-

tions supplied by the vehicle manufacturer. Failure to

follow proper set up instructions could result in

misoperation or damage to the control system.

With the Handset connected , hold down the CONT key and

turn on the key switch. This will place you in the set up mode,

ready to monitor or adjust control function settings.

NOTE:

The term push, means to depress key for approxi-

mately

one second

SET UP MODE

Action

Display shows

Remarks

Hold down CONT,

8888

Segment check

turn on key

displayed

Push function

U 005

Selected

number

function number

is displayed

After one second

085

Stored value for

time delay

the function is

displayed

Push CONT

085

Displayed value

will blink

Change value with

125

Value changes

adjustment knob

while blinking

Push STORE

125

New value

stored and

blinking stops

Push ESC

8888

Segment check

displayed

At this point another function can be monitored/changed

by pushing another function number, or the vehicle can be

placed in the run mode by holding the ESC key down for

one second or longer. The display will return to either the

diagnostics mode or the BDI display or a blank display (

if BDI is not used and there are no fault codes). The

vehicle can now be operated with the handset connected

or the handset can be disconnected before operation.

NOTE: You can return to the segment check mode at any

time, by holding down the ESC key until 8888 appears in

the display.

Содержание EV100 LX


















































































Результаты поиска

Содержание EV100 LX

Отзывы:

Похожие инструкции для EV100 LX

Бренды по названию

Популярные бренды

GE EV100 LX, Инструкция по эксплуатации

Результаты поиска

Содержание EV100 LX

Отзывы:

Похожие инструкции для EV100 LX

Бренды по названию

Популярные бренды