GE EV100 LX Скачать руководство пользователя

Страница: 21 / 81

TRUCK MANAGEMENT MODULE (TMM2)

- is a multi-function accessory card that provides a

horn alarm circuit which blows the horn when the truck is left unattended without the park brake

being set, and also provides a dash board located controlled acceleration adjustment for use by the

operator.

STORED STATUS CODE

- This feature furnishes a function register functional that contains the

last fault that shut down vehicle operation (PMT type fault that is reset by cycling the key switch).

This status code will be over written each time a new status code occurs and can be cleared from

memory by adjusting the value to zero.

ON-BOARD DIAGNOSTICS

- The logic card detects the systems current operating status which

can be displayed to either the Dash Display or the Handset. There are currently over 75 status codes

that are available with systems using Traction and Pump SCR controls and Truck Management

Module (TMM). Along with the status code display from the TMM, the logic card is capable of

reducing the current to the control to alert the operator of a critical fault condition.

BATTERY DISCHARGE INDICATION

- This feature uses the latest in microprocessor technol-

ogy to provide accurate battery state of charge information and supplies passive and active warning

signals to the vehicle operator.

Features and functions:

Displays 100 to 0 percent charge

Display blinks with 20% charge

Disables pump circuit with 10% charge

Auto ranging for 36/48 volt operation

Adjustable for use on 24 to 80 volts

HANDSET

- This is a multi-functional tool to be used with the EV100 LX and LXT SCR controls.

The Handset consist of a Light Emitting Diode (LED) display and a keyboard for data entry.

Features and functions:

Monitor existing system status code for both traction and pump SCR systems

Monitor intermittent random status code

Monitor battery state of charge on LXT systems

Monitor hourmeter reading on traction and pump SCR systems

Monitor or adjust the control functions.

Содержание EV100 LX


















































































Результаты поиска

Содержание EV100 LX

Отзывы:

Похожие инструкции для EV100 LX

Бренды по названию

Популярные бренды

GE EV100 LX, Инструкция по эксплуатации

Результаты поиска

Содержание EV100 LX

Отзывы:

Похожие инструкции для EV100 LX

Бренды по названию

Популярные бренды