GE EntelliGuard GT-L Скачать руководство пользователя страница 61

Страница: 61 / 144

EntelliGuard L

TRIP UNIT

OUBLE

2-27

2.8 TROUBLESHOOTING

Table 3.1 reviews common problems, their possible cause(s) and solution(s). If problems persist please contact our After Sales Service.

Troubleshooting Guide Trip Unit

Possible Cause

Solution

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

The trip unit display is blank.

Ex24 VDC is absent.

-- SOLUTION -->

At least 20% of the current sensor rating, (xCT) must be flowing through the breaker to activate the display.

The trip unit display E03.

Memory failure.

-- SOLUTION -->

Return the unit to GE.

The trip unit display E06.

Internal failure.

-- SOLUTION -->

Return the unit to GE.

2.8 Resolução de problemas

Tabela rever problemas comuns, as suas possíveis causas e soluções. Se o problema persiste por favor contacte o nosso departamento de Pós Venda.

Guia de solução de problemas da Unidade de Disparo Possíveis Causas Soluções

A tela da unidade de disparo está em branco.

--- Os +24 VCC não estão ligados.

Solução -->

--- Ao menos 20% de corrente nominal do sensor, (xTC) deve fluir pelo sensor de modo a alimentar à unidade de disparo.

A tela da unidade de disparo mostra E03

--- Falha de Memória.

--- Devolva a unidade à GE.

A tela da unidade de disparo mostra E06

--- Falha interna.

--- Devolva a unidade à GE.

2.8

USUWANIE USTEREK

Tabela

3.1

zawiera opis najczęściej występujących problemów, ich możliwe przyczyny i sposoby rozwiązania. Jeśli proponowane metody nie przyniosą skutku - prosimy o kontakt

z naszym Działem Serwisu.

Usterki wyzwalacza nadprądowego

--------------------------------------------------------------------
Wyświetlacz wyzwalacza jest wygaszony.

-----------------

--------------------------------------------------

Wyzwalacz nadprądowy wyświetla E03.
--------------------------------------------------------------------
Wyzwalacz nadprądowy wyświetla E06.

Możliwe przyczyny

----------------------------------------------------------------------
Brak zas24 V DC.
-
----------------------------------------------------------------------
Uszkodzona pamięć.
----------------------------------------------------------------------
Błąd wewnętrzny

Rozwiązanie

--------------------------------------------------------------------------------
Aktywacja wyświetlacza wymaga przepływu prądu o wartości
przynajmniej 20% prądu znamionowego przekładnika (xCT).
--------------------------------------------------------------------------------
Przekazać wyzwalacz do GE.
--------------------------------------------------------------------------------
Przekazać wyzwalacz do GE.

Table:
Troubleshooting Guide Breaker

Possible Cause

Solution

Breaker won’t close.

-- Breaker is between CONNECTED, TEST and DISCONNECTED positions.

-- Trip Unit has not been reset.

-- Undervoltage Release is installed but not energized.

-- Interlocks installed.

-- Racking handle inserted.

-- SOLUTION -->

-- Rack circuit breaker to CONNECTED, TEST or DISCONNECTED remove racking handle and close circuit breaker.

-- Push orange button on Trip Unit and close circuit breaker.

-- Energize Undervoltage Release and close circuit breaker.

-- Remove interlocks.

-- Remove handle and close circuit breaker.

-- Check operational diagram (chapter 1.4) and trip the relevant circuit breaker.

Breaker closes then opens instantaneously.

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

-- Trip Unit settings are incorrect.

-- Remote Rogowski coil is incorrectly installed.

-- SOLUTION -->

-- Ensure the protection limits setting matches system loads. Ensure inputs are set to normally closed trip without a signal applied.

-- Re-position Coil.

Motor won’t charge.

-- Ensure Motor Actuator is installed.

-- SOLUTION -->

-- Install Motor Actuator.

DC closing coil or Undervoltage Release won’t operate.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------

-- Ensure the correct polarity of the connection to the secondary isolating contacts.

-- SOLUTION -->

-- Refer to wiring schematic (see Section 1.3).

Circuit breaker won’t rack into cassette.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

-- Ensure breaker is pushed fully from the maintenance position to DISCONNECTED.

-- Racking drive not in DISCONNECTED position.

-- SOLUTION -->

-- Push breaker into DISCONNECTED position.

-- Ensure racking drive is in DISCONNECTED position.

Cannot insert racking handle.

-- Shutter padlocks are installed.

-- Key locks are installed.

-- SOLUTION -->

-- Remove locks.

Circuit breaker will not go into the DISCONNECTED position.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------

-- Mis insertion feature is incorrectly set.

-- Circuit breaker is incorrect for given cassette.

-- SOLUTION -->

-- Reset Mis insertion feature.

-- Ensure circuit breaker and cassette go together.

Trip Unit healthy indicator not working. (Fig 2.1)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

-- Ensure Trip Unit, if installed, is energized.

-- Insufficient primary current to power the unit.

-- SOLUTION -->

-- Install Trip Unit, if not installed.

-- Trip Unit will power with 40% In single phase, and 20% In 3 phase current.