GE Druck ADTS 2 Series Скачать руководство пользователя страница 10

Страница: 10 / 70

Druck ADTS 2XX User Manual

viii

K0451 Issue No. 1

Glossary

Terminology

The terminology used in this manual is specific and individual interpretation must not be introduced. The
terms are defined as follows:

Adjust

To bring to a more satisfactory state; to manipulate controls, levers, linkages, etc. to return
equipment from an out-of-tolerance condition to an in-tolerance condition.

Align

To bring into line; to line up; to bring into precise adjustment, correct relative position or
coincidence.

Assemble:

To fit and secure together the several parts of; to make or form by combining parts.

Calibrate:

To determine accuracy, deviation or variation by special measurement or by comparison with
a standard.

Check:

Make a comparison of a measure of time, pressure, temperature, resistance, dimension or
other quality with a known figure for that measurement.

Disconnect: To detach the connection between; to separate keyed or matched equipment parts.

Dismantle:

To take apart to the level of the next smaller unit or down to all removable parts.

Examine:

To perform a critical visual observation or check for specific conditions; to test the condition of.

Fit:

Correctly attach one item to another.

Inspect:

Review the work carried out by Specialists to ensure it has been performed satisfactorily.

Install:

To perform operations necessary to properly fit an equipment unit into the next larger
assembly or system.

Maintain:

To hold or keep in any particular state or condition especially in a state of efficiency or validity.

Operate:

Make sure that an item or system functions correctly as far as possible without the use of test
equipment or reference to measurement.

Readjust:

To adjust again; to move back to a specified condition; to bring back to an in-tolerance
condition.

Содержание Druck ADTS 2 Series






































































Результаты поиска

Содержание Druck ADTS 2 Series

Отзывы:

Похожие инструкции для Druck ADTS 2 Series

Бренды по названию

Популярные бренды

GE Druck ADTS 2 Series, Руководство пользователя

Результаты поиска

Содержание Druck ADTS 2 Series

Отзывы:

Похожие инструкции для Druck ADTS 2 Series

Бренды по названию

Популярные бренды