GDS Compuprint 2056 Скачать руководство пользователя | Manualshive

Страница: 15 / 68

background image

User Manual 2056

MAN10xxx-01 7

1.8 Connecting the Printer to Your Computer

The printer configures with a parallel interface, two USB interfaces, a serial interface or an

Ethernet interface. (Please take the specific interface as standard) Connect the printer to

the computer with the correct cables. Before you begin, place the printer upright, as shown

in figure 1-12.

1.8.1 Connecting to the Parallel Interface

1. Turn off both the computer and the printer. Plug the parallel interface cable into the

printer’s parallel interface. Squeeze the wire clips on both sides of the connector and

make the connector fixed. (Shown as figure 1-13)

2.

Plug the other end of the cable into the computer's parallel interface, and make sure it is

connected firmly.

Figure 1-12 Lay the rear part of the printer upwards

Figure 1-13 Connect to the parallel interface

Serial interface

USB interface

Parallel interface

USB interface

Ethernet interface

Parallel interface

Parallel interface cable

Wire clips

Note: Before connecting the parallel interface or the serial interface, please

make sure the power of the printer is shut down. Only after tightening
the cable, could you turn on the printer, or it would damage the printer.

«
...
13
14
15
16
17
...
»

Содержание Compuprint 2056





































































Отзывы:

Нет отзывов

Похожие инструкции для Compuprint 2056

Бренд: Canon Страницы: 58

image Prograf iPF680 Series

Бренд: Canon Страницы: 132

Бренд: Canon Страницы: 44

imageClass LBP6230dw

Бренд: Canon Страницы: 16

Бренд: Canon Страницы: 2

imageprograf IPF785

Бренд: Canon Страницы: 42

Бренд: Canon Страницы: 148

Color Bubble Jet BJC-8200

Бренд: Canon Страницы: 6

Color Bubble Jet BJC-1000 Series

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Color Bubble Jet BJC-8200

Бренд: Canon Страницы: 105

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 68

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

imagePROGRAF iPF830

Бренд: Canon Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды