Gates Underwater Products EX1R Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 26

background image

Gates Underwater Products, Inc

13685 Stowe Drive • Poway, CA • 92064 • 858.391.0052 • 800.875.1052 • 858.391.0053

[email protected] • www.GatesHousings.com

10

01/13/10

Handle Adjustment

9

Loosen the thumbscrew

at the top of each handle and move forward or back for

optimal control access.

9

Tighten the thumbscrews

to secure the handle in position.

Foot Plate Installation

9

Remove the knurled brass retainer

from the screw on the dovetail and slide

the dovetail onto the housing from front to back until fully seated. Replace the knurled
brass retainer to secure the foot plate.

Slide the foot onto the dovetail

and secure with the knurled

brass nut. Foot slides from

back to front.

Loosen the thumbscrew

to adjust the handle

forward and back for best

position.

«
...
8
9
10
11
12
...
»

Содержание EX1R



























Отзывы:

Нет отзывов

Похожие инструкции для EX1R

Бренд: AAT Страницы: 6

Бренд: Kabuto Страницы: 25

TENSIONED CONTOUR ELECTROL

Бренд: Da-Lite Страницы: 8

Бренд: Dacor Страницы: 4

Бренд: e-motion Страницы: 2

Бренд: Hach Страницы: 44

Бренд: Habasit Страницы: 14

Бренд: Hama Страницы: 60

Бренд: BAFANG Страницы: 4

Бренд: Napoleon Страницы: 4

Бренд: Napoleon Страницы: 4

Бренд: Napoleon Страницы: 2

Бренд: Varta Страницы: 2

Бренд: Dometic Страницы: 162

Бренд: Firecom Страницы: 8

Бренд: Horn Tools Страницы: 6

Бренд: PCB Piezotronics Страницы: 9

Бренд: 4 tec SENSORTECHNOLOGY Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды