Gates Underwater Products EX1R Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 26

background image

Gates Underwater Products, Inc

13685 Stowe Drive • Poway, CA • 92064 • 858.391.0052 • 800.875.1052 • 858.391.0053

[email protected] • www.GatesHousings.com

26

01/13/10

Lighting Systems

Your housing comes ready to accept different lighting systems depending on your
requirements. If you purchased lighting systems from Gates you will find a separate
document to guide you through installation to your Gates EX1R housing. You can also
find it on Gates web site at

www.GatesHousings.com

.

Housing Care and Maintenance

Proper care of your Gates housing is important to provide you reliable operation and
long life. You’ll find all the guidelines in the “Housing Care and Maintenance” document
included with your Gates housing. You can also find it on Gates web site at

www.GatesHousings.com

.

O-Ring Care and Maintenance

Your Gates housing has 2 serviceable o-rings. One is located between the mating
halves of the housing (the large orange one) and the other is located on each Port.

Servicing the o-rings is easy and covered in the “Housing Care and Maintenance”
document in this package. It can also be found on the Gates website at

www.gateshousings.com

.

a

Caution

:

Do not lubricate the large orange o-ring! It is a special silicone o-

ring and can be damaged by petroleum-based lubricants.

a

Caution

:

Never

use metal tools or objects for removing o-rings!

Customer Support

If you have any questions or require further assistance with your Gates housing, contact
your dealer or Gates directly and we’ll be happy to assist.

Email:

[email protected]

Phone:

858-391-0052

Fax:

858-391-0053

«
...
24
25
26

Содержание EX1R



























Отзывы:

Нет отзывов

Похожие инструкции для EX1R

Бренд: CAB Страницы: 10

Бренд: Jeda Страницы: 8

Бренд: oliser Страницы: 6

Бренд: Carefree Страницы: 12

Retrotech RTX-68D-CHG

Бренд: Dakota Digital Страницы: 4

Бренд: AZZA Страницы: 18

Бренд: Digitus Страницы: 9

Бренд: REV Страницы: 2

Бренд: Farad Страницы: 8

Бренд: Quantum Страницы: 3

Big Daddy Insta-Net

Бренд: Izzo Golf Страницы: 2

Бренд: Pro-Ject Audio Systems Страницы: 7

Бренд: SOLAC Страницы: 13

ecoCRAFT VKK GB 1206/3-E-H

Бренд: Vaillant Страницы: 16

Бренд: Kodak Страницы: 2

signal mirror 2005-2009 Ford Mustang

Бренд: muth Страницы: 9

Бренд: Soehnle Страницы: 20

Бренд: Omegon Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды