Gates Underwater Products EX1R Скачать руководство пользователя

Страница: 25 / 26

Gates Underwater Products, Inc

13685 Stowe Drive • Poway, CA • 92064 • 858.391.0052 • 800.875.1052 • Fax 858.391.0053

[email protected] • www.GatesHousings.com

01/13/10

Loosen the thumbscrews,
slide the monitor onto the
top rail, then tighten
gently to secure.

Connect and secure the
video connection. The 6
pin HD connector is
shown. Other monitors
may use single pin SD
connector.

Monitor mount and connection

Slide the dovetail and monitor

into the grooves on top of the housing and tighten in

place with the thumbscrews.

Plug in the monitor cable

to the housing bulkhead connector, which is found on the

right side of the housing. You will have either a single pin standard definition (SD)
connection or a 6 pin high definition (HD) connection.

Caution

If you are not using the monitor for any reason, do not plug the RCA

connector into the camera.

Verify operation

once again to ensure all is working properly prior to use in water.

Содержание EX1R



























Результаты поиска

Содержание EX1R

Отзывы:

Похожие инструкции для EX1R

Бренды по названию

Популярные бренды

Gates Underwater Products EX1R, Руководство по установке, использованию и уходу

Результаты поиска

Содержание EX1R

Отзывы:

Похожие инструкции для EX1R

Бренды по названию

Популярные бренды