background image

Owner's Manual

-28-

Daily inspection before riding

prior to each use of your 

Gas Gas

 motorcycle it is necessary to carry out the 

following checks:

is there enough fuel?

 open the fuel cap and, by moving the motorcycle sideways 

with the handlebar, you will see and hear the fuel, so you will know the approximate 
contents.  

is the fuel tap open?

 The fuel tap (1) has three positions: open: on (tap down), 

closed: off (horizontal tap to the right side of the motorcycle) and reserve. REs 
(horizontal tap to the left side of the motorcycle). if the tap is in the off position 
there is no fuel to the carburettor, the motorcycle will not run, this position is used 
only when the engine is stopped. if you can see that there is little fuel in the tank, it 
should be started with the tap in the REs position, and go immediately to refuel. if 
everything is correct you must always use the tap in the on position.

note:

 always turn off the fuel tap (off position) when the engine stops.

What is the oil level in the engine?

 check through the oil sight glass (2) that the 

level is suitable, if necessary, add more oil. 

What is the coolant level? 

By removing the filler cap from the radiator, the coolant 

level can be checked. This should be just below the metal rim (3), if necessary, add 
more coolant.

 DanGer

do not open the plug while the engine is hot, you risk serious burns.

1

2

3

Содержание Enduro 2T 250 2018














































































Отзывы: