GAS GAS Enduro 2T 250 2018 Скачать руководство пользователя | Manualshive

Страница: 42 / 77

background image

Owner's Manual

-42-

11.-Muffler fiBre

The muffler of your

Gas Gas

is an absorption muffler. The absorbent element is

the muffler fibre. if there is an increase in exhaust noise, the muffler fibre must be
replaced.

Replacing the muffler fibre

once the muffler is removed, (see Replacing the muffler). Remove the 4 screws (1).
1.  Remove the inside of the muffler.
2.  Replace the muffler fibre (2) by winding it to the inner tube.
3.  insert the fibre around the exhaust pipe (3) into the rear end of the muffler.
4.  Reassemble the assembly.

Maintenance

1

2

3

«
...
40
41
42
43
44
...
»

Содержание Enduro 2T 250 2018














































































Отзывы:

Нет отзывов

Похожие инструкции для Enduro 2T 250 2018

Бренд: LAZER Страницы: 19

Бренд: hepco & becker Страницы: 6

Бренд: KEEWAY Страницы: 164

Бренд: SCHUBERTH Страницы: 41

Бренд: kellermann Страницы: 2

Бренд: BMW Motorrad Страницы: 146

690 SMC R 2016 Series

Бренд: KTM Страницы: 18

Бренд: N-Com Страницы: 2

Бренд: Athena Страницы: 88

Бренд: Rockford Fosgate Страницы: 8

RSV MILLE SPORT - PART 2 1999

Бренд: APRILIA Страницы: 47

Бренд: APRILIA Страницы: 288

Pegaso 650 I.E.

Бренд: APRILIA Страницы: 320

Бренд: Honda Страницы: 36

Бренд: APRILIA Страницы: 311

Бренд: Honda Страницы: 177

Бренд: Milwaukee Страницы: 7

Бренд: Salewa Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды