Gardena SILENO+ Series Скачать руководство пользователя

Страница: 14 / 52

CAUTION: Do not lift the product when

it is parked in the charging station. It

can damage the charging station

and/or the product. Press the STOP

button and pull the product out of the

charging station before lifting it.

2.3.4 Maintenance

WARNING: When the product is

turned upside down the main switch

must always be in the

0 position.

The main switch should be set in the

position before all work on the chassis

of the product, such as cleaning or

replacing the blades.

CAUTION: Never use a high-pressure

washer or even running water to clean

the product. Never use solvents for

cleaning.

CAUTION: Use the plug to disconnect

the charging station before any

cleaning or maintenance of the

charging station or the loop wire.

Inspect the product each week and replace any

damaged or worn parts. Refer to

Introduction -

maintenance on page 31.

2.3.5 In the event of a thunderstorm

To reduce the risk of damage to electrical

components in the product and the charging

station, we recommend that all connections to the

charging station are disconnected (power supply,

boundary wire and guide wire) if there is a risk of

a thunderstorm.
1. Mark the wires to simplify reconnecting. The

charging station’s connections are marked

AR, AL and G1.

2. Disconnect all connected wires and the

power supply.

3. Connect all the wires and the power supply

if there is no longer a risk of thunder. It is

important that each wire is connected to the

right place.

14 - Safety

1025 - 001 - 23.01.2019

Содержание SILENO+ Series





















































Результаты поиска

Содержание SILENO+ Series

Отзывы:

Похожие инструкции для SILENO+ Series

Бренды по названию

Популярные бренды

Gardena SILENO+ Series, Руководство оператора

Результаты поиска

Содержание SILENO+ Series

Отзывы:

Похожие инструкции для SILENO+ Series

Бренды по названию

Популярные бренды