Gardena SILENO+ Series Скачать руководство пользователя

Страница: 5 / 52

26. Measurement gauge for help when installing

the boundary wire (the measurement gauge

is broken loose from the box)

27. Operator’s Manual and Quick Guide
28. Extra blades
29. Low voltage cable
30. Alarm decal
31. USB cable for Software-Updates
32. smart Gateway (only for GARDENA

R160LiC)

33. smart Gateway LAN-cable (only for

GARDENA R160LiC)

34. smart Gateway Power Supply (only for

GARDENA R160LiC)

1.4 Symbols on the product

These symbols can be found on the product.

Study them carefully.

WARNING: Read the

user instructions before

operating the product.

WARNING: Operate the

disabling device before

working on or lifting the

machine.
The product can only start

when the main switch is

set to

1 and the correct

PIN code has been en-

tered. Turn the main

switch to

0 before carry-

ing out any inspections

and/or maintenance.
WARNING: Keep a safe

distance from the ma-

chine when operating.

Keep your hands and feet

away from the rotating

blades.
WARNING: Do not ride

on the machine. Never

put your hands or feet

close to or under the ma-

chine.
Never use a high-pres-

sure washer or even run-

ning water to clean the

product.
Lock function

This product conforms to the

applicable EC Directives.

Noise emission to surroundings. The

product’s emissions are set out in

Technical data on page 47 and on the

rating plate.

It is not permitted to dispose this

product as normal household waste.

Ensure that the product is recycled in

1025 - 001 - 23.01.2019

Introduction - 5

Содержание SILENO+ Series





















































Результаты поиска

Содержание SILENO+ Series

Отзывы:

Похожие инструкции для SILENO+ Series

Бренды по названию

Популярные бренды

Gardena SILENO+ Series, Руководство оператора

Результаты поиска

Содержание SILENO+ Series

Отзывы:

Похожие инструкции для SILENO+ Series

Бренды по названию

Популярные бренды