Galil DMC-4040 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 284

background image

Next you need to increase the value of KP gradually (maximum allowed is 1023.875). You can monitor the
improvement in the response with the Tell Error instruction

KP 10 <return>

Proportion gain

TE A <return>

Tell error

As the proportional gain is increased, the error decreases.

Again, the system may vibrate if the gain is too high. In this case, reduce KP by about 20%. Typically, KP should
not be greater than KD/4 (only when the amplifier is configured in the current mode).

Finally, to select KI, start with zero value and increase it gradually. The integrator eliminates the position error,
resulting in improved accuracy. Therefore, the response to the instruction

TE A <return>

becomes zero. As KI is increased, its effect is amplified and it may lead to vibrations. If this occurs, simply reduce
KI. Repeat tuning for the B, C and D axes.

Note:

For a more detailed description of the operation of the PID filter and/or servo system theory, see

Theory of Operation

Design Examples

Here are a few examples for tuning and using your controller. These examples have remarks next to each command
- these remarks must not be included in the actual program.

Example 1 - System Set-up

This example assigns the system filter parameters, error limits and enables the automatic error shut-off.

Instruction

Interpretation

KP10,10,10,10

Set gains for a,b,c,d (or A,B,C,D axes)

KP*=10

Alternate method for setting gain on all axes

KPA=10

Method for setting only A (or X) axis gain

KPX=10

Method for setting only X (or A) axis gain

KP, 20

Set B axis gain only

Instruction

Interpretation

OE 1,1,1,1,1,1,1,1

Enable automatic Off on Error function for all axes

ER*=1000

Set error limit for all axes to 1000 counts

KP10,10,10,10,10,10,10,10

Set gains for a,b,c,d,e,f,g,and h axes

KP*=10

Alternate method for setting gain on all axes

KPA=10

Alternate method for setting A axis gain

KP,,10

Set C axis gain only

KPD=10

Alternate method for setting D axis gain

KPH=10

Alternate method for setting H axis gain

Example 2 - Profiled Move

Rotate the A axis a distance of 10,000 counts at a slew speed of 20,000 counts/sec and an acceleration and
deceleration rates of 100,000 counts/s2. In this example, the motor turns and stops:

Instruction

Interpretation

PR1000

Distance

Chapter 2 Getting Started

•

25

DMC-40x0 User Manual

«
...
32
33
34
35
36
...
»

Содержание DMC-4040





























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DMC-4040

Бренд: Gantner Страницы: 56

Бренд: GE Страницы: 8

Бренд: FrSky Страницы: 2

Бренд: Manfrotto Страницы: 16

Бренд: Cansec Страницы: 45

Бренд: Cansec Страницы: 43

Бренд: Cansec Страницы: 32

Бренд: Eaton Страницы: 28

Бренд: Parallel Страницы: 16

Бренд: V2 Страницы: 46

FOUNDATION 3730-5

Бренд: Samson Страницы: 132

Бренд: Samson Страницы: 68

Бренд: Samson Страницы: 128

Бренд: Samson Страницы: 68

Бренд: X-POWER Страницы: 24

Бренд: Samson Страницы: 80

Бренд: Haehne Страницы: 44

Бренд: Watts Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды