FUTABA T12Z Скачать руководство пользователя страница 14

- 14 - 

4. Use the cursor lever to move the cursor to the 

CONTROL display and push the DATA button. The 
control selection screen opens. Select the control which 
is to adjust the limit position.

 

5. Use the cursor lever to move the cursor to the HI 

RANGE display. Use the dial to set the limit adjustment 
range upper limit. An adjustment range gauge is 
displayed.

 

6. Use the cursor lever to move the cursor to the LOW 

RANGE display. Use the dial to set the limit adjustment 
range lower limit. An adjustment range gauge is 
displayed.

 

 
 

PCM-G3 COMMUNICATION MODE

 

Two types of PCM-G3 communication modes can be selected: 
Mode A and Mode B. Mode A is the conventional mode. Mode 
B is a mode with enhanced communication quality. Choose the 
mode matched to the usage environment.

 

 

 

Setting method

 

1. Open the frequency setting screen from the Linkage 

Menu.

 

2. Open the modulation type setting screen from the 

frequency setting screen.

 

3. Use the cursor lever to move the cursor to PCM-G3 

mode selection.

 

4. Use the dial to select the mode, and push the DATA 

button.

 

5. Use the cursor lever to move the cursor to PCM G3, and 

push the DATA button.

 

6. A change confirmation screen is displayed. When the 

DATA button is pushed, the modulation type is changed 
and the Startup screen appears.

 

 

Notes

·

 When using communications mode B, a receiver 

compatible with mode B is necessary. (The R5014DPS is 
not mode B compatible.)

 

·

 In communication mode B, the servo response to stick 

operation is approximately 20% lower than that of mode 
A.

 

 
 

PCM1024 CH10

 

10

th

 channel is added to the PCM1024 mode. DG2 is added on 

the function menu at the PCM1024 mode. It is 10

th

 channel 

control selection.

 

 

Notes

·

 The current 9ch receiver must be modified at the 

servicing department to implement the 10

th

 channel.

 

 
 
 
 
 

Modulation PPM mode

 

Added the modulation polarity selection at PPM mode.

 

Added 12 channels PPM mode.

 

 

 

 

 
 
 

Setting method

 

1. Open the frequency setting screen from the Linkage 

Menu.

 

2. Open the modulation type setting screen from the 

frequency setting screen.

 

3. Use the cursor lever to move the cursor to PPM setting 

item.

 

4. Use the dial to select the mode, and push the DATA 

button. 
CH : 8CH or 12CH, POL : STD or INV, OFFS : N1.5 or 
N1.3 
OFFS is appeared at only selected 12CH.

 

5. Use the cursor lever to move the cursor to PPM, and 

push the DATA button.

 

6.A change confirmation screen is displayed. When the 

DATA button is pushed, the modulation type is changed 
and the Startup screen appears.

 

 

Notes

·

 The PPM setting of “8CH” and “STD” corresponds to 

FUTABA receivers.

 

 
 

PITCH CURVE [Model Menu] 

A function which copies a curve containing the pitch trim 
(hovering pitch, low side pitch, high side pitch) when the curve 
mode is LINE and SPLINE was added.

 

 

 

Setting method

 

1. Open the pitch curve setting screen.

 

2. Set the curve mode to LINE or SPLINE.

 

3. Set the pitch trim (hovering pitch, low side pitch, high 

side pitch).

 

4. Operate the pitch trim (hovering pitch, low side pitch, 

high side pitch).

 

5. Use the cursor lever to move the cursor to COPY, and 

push the DATA button for at least 1 second.

 

Mode selection

Copy function added

Polarity selection 

STD or INV

CH selection

8CH or 12CH

Neutral pulse width selection.

N1.5 or N1.3

(This appears at only 12CH.)

Содержание T12Z

















Отзывы: