FUTABA T12Z Скачать руководство пользователя страница 13

- 13 - 

2. Mixing using logic switches as ON/OFF switches is 

forcibly switched to the condition single mode. Switching 
to the condition group mode is impossible until the logic 
switches are released.

 

 

 

 
 

PROGRAM MIXING [Model Menu] 
Speed Mode 

This function lets you set the operation switch at the program 
mixing master side. The servo can be operated outside the set 
curve by switch operation by using this function.

 

 

 
 

Setting method

 

1. Set program mixing to the curve mode. The ACT, 

SWITCH, etc. setting screen shown above appears.

 

2. Use the cursor lever to move the cursor to speed mode 

selection. Use the dial to select the master mode, and 
push the DATA button.

 

3. Set the in speed and out speed.

 

4. Set the toggle switch to program mixing master.

 

5. When the switch set to master is operated, the master 

position marker of the curve is shifted at the set servo 
speed and the slave function operates along the curve 
setting. In the below example, when SW-F is operated, 
the slave auxiliary 1 function automatically operates 
along the EXP1 curve.

 

 

 
 

MODEL TYPE [Linkage Menu]

 

  The H-4X mode has been added to the swash types available.   
The H-4X swash type is the same as the H-4 type, except the 
control points are rotated 45 degrees.

 

 

 
 

MOTOR MIXING [Model Menu] 

Motor mixing was added to airplane model. In addition, when 
the power is turned on in the mixing on state, a warning 
message is output.

 

 
 

SWASH RING [Model Menu] 

This function limits the swash travel to within a fixed range to 
prevent damaging of the swash ring by simultaneous operation 
of the ailerons and elevators. It is effective in 3D aerobatics 
which use a large travel.

 

 

 
 

Setting method

 

1. Open the swash ring setting screen by selecting 

SWASH RING from the linkage menu.

 

2. The operating range display area mark shows the stick 

position. The vertical direction shows the aileron travel. 
When ACT is displayed by pushing the ACT/INH button, 
the swash ring function is activated, and a circle is 
displayed in the operating range display area. Stick 

operation is limited to within the area of this circle.

 

3. Use the cursor lever to move the cursor to the rate 

display. Use the dial to set the rate. The adjustment 
range is 50~200%. Adjust the rate to maximum swash 
tilt.

 

 
 

THROTTLE LIMITER [Model Menu] 

This function sets the upper limit position of the throttle curve. 
Limit position adjustment can be assigned to an arbitrary control. 
Adjustment range upper and lower limits can be set.

 

 

 

 
Setting method

 

1. Open the throttle limiter setting screen by selecting THR 

LIMITER from the Model Menu.

 

2. Use the cursor lever to move the cursor to the ACT/INH 

display. Use the dial to select ACT, and push the DATA 
button. ON or OFF is displayed.

 

3. Use the cursor lever to move the cursor to the SWITCH 

display and push the DATA button. The switch selection 
screen opens. Select the throttle limiter function ON/OFF 
switch.

 

Switch

 

Combination logic

 

SW1

SW2

AND OR  Ex-OR 

off off off off  off 
off on off on  on 
on off off on  on 
on on on on  off 

Speed mode selection

Switched to condition single mode

Logic mode

Adjustment range gauge

 

Throttle curve

Limit control

Limit control position

 

Master: SW-F

Operating range 
display area

ACT/INH 

Rate

 

Содержание T12Z

















Отзывы: