FUTABA T12Z Скачать руководство пользователя страница 11

- 11 - 

( Update Modification Contents in the past ) 

 
 

STICK SETTING [System Menu] 

This function sets the servo response speed (response) and dead 
band width (hysteresis) relative to stick operation for each 
condition. The operation feel of the stick can be adjusted to 
match the in-flight aerobatics. 
 

Call the setting screen shown below by selecting [STICK 
SETTING] from the System Menu.

 

 

 
 

Response adjustment

 

1. Use the cursor lever to move the cursor to the set value 

display of the stick whose response you want to adjust.

 

2. Use the dial to set the response.

 

Initial value : 4

 

Adjustment range : 1~16 (The larger the adjustment 
value, the slower the response.)

 

 

Hysteresis adjustment

 

1. Use the cursor lever to move the cursor to the set value 

display of the stick whose hysteresis you want to adjust.

 

2. Use the dial to adjust the response.

 

Initial value : 1

 

Adjustment range : 0~32 (The larger the adjustment 
value, the larger the hysteresis.) 

 
 

MULTIPROP CHANNEL 

[Linkage Menu] 

One channel can be expanded to 8 channels by using an 
MPDX-1 (Multiprop Decoder). Up to two MPDX-1 can be used 
with the 12Z system.

 

 

Multiprop function assignment

 

1. Open the function setting screen of the Linkage Menu, 

and set the function of the channel to which you want to 
connect the 

MPDX-1

 to 

MULTIPROP1

 or 

MULTIPROP2

.

 

 

 

 

Operation control setting method

 

1. After assigning the function as described above, use the 

cursor lever to move the cursor to MP CH of the channel 

you want to set to multiprop. Push the DATA button to 
display the setting screen shown below.

 

 

2. Use the cursor lever to move the cursor to CH 

CONTROL of the multiprop channel you want to set. 
Push the DATA button to display the control selection 
screen. Select control.

 

 

Reverse setting

 

*

Use this function when you want to reverse the direction of servo 
operation.

 

1. Open the servo reverse setting screen of the Linkage 

Menu. Use the cursor lever to select MP CH of the 
channel you want to set to multiprop. Push the DATA 
button.

 

 

 
2. The multiprop channel reverse setting screen is 

displayed. Use the cursor lever to move the cursor to the 
channel whose direction of operation you want to reverse. 
Use the dial to switch between NORM (normal) and REV 
(reverse), and push the DATA button.

 

 

End point adjustment

 

1. Open the end point (ATV) setting screen of the Linkage 

Menu. Use the cursor lever to select MP CH of the 
channel you want to set to multiprop. Push the DATA 
button.

 

 

2. The multiprop channel end point (ATV) setting screen is 

displayed. Use the cursor lever to move the cursor to the 
channel whose end point you want to adjust. Use the dial 
to change the rate. (Left and right, up and down can be 
adjusted individually.)

 

 

*

When both MULTIPROP1 and MULTIPROP2 are set, pushing the 
cursor lever switches the MULTIPROP1 and MULTIPROP2 displays. 

Response

setting

Hysteresis setting 

Condition 
group/single 
switching 

Screen with MULTIPROP1 and MULTIPROP2 set 

Содержание T12Z

















Отзывы: