FUTABA T12Z Скачать руководство пользователя страница 12

- 12 - 

Servo monitor

 

1. When the cursor lever is pushed, the normal channel 

display and multiprop channel display are switched.

 

 

<Normal channel display> 

 

 

<Multiprop channel display>

 

 
 
 

LOGIC SWITCH [Model Menu]

 

The logic switch function lets you turn operation on and off by 
combining multiple switches. For instance, “Turn on the 
function when 2 switches are turned on simultaneously” can be 
set.

 

 

·

Up to 4 switches can be combined.

 

·

Up to 10 circuits can be used with the condition switches and 

up to 8 circuits can be used with the ON/OFF switch of each 

mixing function, except airplane snap roll.

 

 

<Mixing ON/OFF switch display> 

(example of program mixing)

 

 
 

Setting procedure

 

1. Use the cursor lever to move the cursor to the switch 

display of the function you want to set. Push the DATA 
button.

 

2. The switch selection screen shown below is displayed.

 

 

<Mixing ON/OFF switch display> 

(example of program mixing)

 

 
3. Use the cursor lever to move the cursor to the switch 

mode. Use the dial to select the single switch mode or 
logic switch mode, and push the DATA button. The single 
switch mode is used with individual switches, the same 
as in the past. When switched to the logic switch mode, 
the switch mode and switches are displayed as shown 
below. ON/OFF is determined by the combination of the 
switch and logic mode displayed at the top and bottom.

 

 

 

4. Use the cursor lever to move the cursor to the logic 

mode. Use the dial to select the logic from the three 
types AND, OR, and Ex-OR, and push the DATA button. 
Logic operation is shown in the table at below right. For 
AND, both switches are ON, for OR, either one of the 
switches is ON, and for Ex-OR, when the two switches 
are in different states, the result is ON.

 

 

 

 

5. Use the cursor lever to move the cursor to the top or 

bottom switch mode. Use the dial to select the logic 
switch mode, and push the DATA button. Switch display 
is added to each. A combination of up to 4 switches can 
be registered in this manner. When 3 or more switches 
are registered, the left and right switch combinations 
surrounded by the frame are judged first. Next, the 
combination in the judged frame are judged by the logic 
displayed at the far right side. Finally, ON/OFF is 
decided.

 

 

 

*

In the above example, first SW-A and SW-B are judged by AND 
condition and then SW-C and SW-D are judged by AND condition. 
Lastly, the result of judgment of the SW-A and SW-B judgment result 
and SW-C and SW-D judgment result by OR condition becomes the 
final result. In this case, when SW-A and SW-B are simultaneously ON 
or SW-C and SW-D are simultaneously ON, the result is ON.

 

 
 

Restrictions

1. Logic switches can be used in mixing the ON/OFF 

setting with up to 8 circuits for each condition. In 
condition switching, it can be used with up to 10 circuits. 
When logic switches exceeding the maximum settable 
value are selected, an error message is displayed. 
Release the unnecessary logic switches and then 
reselect.

 

 

 

Switch mode 

Switch 

Switch state display (INH, ON, OFF)

 

(Condition switch: ON and OFF)

 

Judgment(1)

Judgment(2)

Judgment(3) 

Mode selection

Содержание T12Z

















Отзывы: