FUTABA FMT-03 Скачать руководство пользователя

Страница: 32 / 68

<Basic Operation>

Key lock

To prevent the data from being changed by erroneous pushing of the edit dial during flight, a

function which makes an edit dial impossible temporarily.

How to lock

1. The home screen is displayed.
2. Push the S1 button for about 1 second.

"LOCK" is displayed and the edit dial is

disabled.

How to unlock

1. Push the S1 button for about 1 second in the

edit dial locked state. The edit dial is enabled

again.

STARTUP LOCK

Auto Lock functions automatically when the

model changes or power is turned on.

*To temporarily allow access to the FMT-03 programming

push and hold the S1 bitton for one second. Please note,

the Auto Lock function timer will resume immediately once

again.

*A PIN can also be set to protect the set data.

AUTOMATIC LOCK

Auto Lock functions automatically when there is

no operation from the HOME screen display for a

chosen number of seconds.

*Two kinds of automatic locks can be

chosen by

[DISPLAY]

[SYSTEM MENU]

Содержание FMT-03





































































Результаты поиска

Содержание FMT-03

Отзывы:

Похожие инструкции для FMT-03

Бренды по названию

Популярные бренды

FUTABA FMT-03, Инструкция по эксплуатации

Результаты поиска

Содержание FMT-03

Отзывы:

Похожие инструкции для FMT-03

Бренды по названию

Популярные бренды