8. NBDP PREPARATIONS
8-8
3. Group Name is selected. Enter a suitable group name. (10 group names can be entered.
If you attempt to enter more, the message “Scan group memory is full. Press any key to
escape.” appears. Press any key and then delete unnecessary group names to enter
new ones. If the group name already exists, the message “Scan group by that name
already exists. Press any key to escape.” appears. Press any key and change the scan
group name.)
4. Press the
↓
key to select Ch Dwell Time. Enter channel dwell time in seconds. Dwell
time is the time in seconds the receiver waits on each channel in a scan group before it
selects the next frequency.
5. Press the
↓
key to select Mode, and then select the communication mode; AUTO, ARQ
or FEC.
Note:
AUTO is used to register scanning channel group when both ARQ and FEC exist
in the same Scanning Channel Group. When you select scan group by the Call Station
menu, set Mode to FEC. See section 10.3.
6. Press the
↓
key to select Auto Search. Select Auto Search to ON or OFF.
Auto Search ON:
The radio stops scanning when it finds the strongest signal (highest
S/N ratio). To find the strongest signal, the radio scans all channels,
which can take some time. Therefore, use this setting where signal
propagation is poor.
Auto Search OFF:
The radio stops scanning on the first signal it finds. We recommend
that you set Auto Search to OFF when signal propagation is good.
7. Press the
↓
key to select line no. 1 in the Scanning Set Up window.
8. Enter channel number (ITU or user channels) and press the
→
key to select “Scan.” (If
you enter an invalid channel, the message “Channel by that number does not exist.
Press any key to escape.” appears. Press any key and reenter channel.)
9. Press the
↓
key to select line No. 2. Enter channel number.
10. Enter other channel numbers and then press the
Enter
key. A confirmation message
appears.
11. Press the
Enter
key again to save the data. The group name is displayed in the
Scanning Group List window.
12. To continue, press the
Enter
key twice and then repeat steps 3-11.
13. Press the
Esc
key to close the menu.
8.5.2
Editing/Deleting scan channel groups
1. Press the function key
F5
and then the
3
key.
2. Press the
↓
key to select scan group name from the Scanning Group List.
3. Press the
→
key to select Change and press the
Enter
key.
4. Press the
↓
key to place the cursor on the field (channel) to change.
5. Do one of the following:
Editing channels:
Press the
Backspace
key to delete the channel number and then enter
new channel number.
Adding channels:
Enter channel number on a blank line.
Deleting scan group:
Delete group name with the
Backspace
key.
Disabling channels temporarily:
Press the
←
key to underline Pass.
6. Press the
Enter
key twice.
7. Press the
Esc
key to close the menu.
Содержание FS-2575
