Fukuda Denshi HR-800 Скачать руководство пользователя страница 25

Страница: 25 / 70

1. Open/Close Lever

Is used to open the paper holder.

2. Paper Holder

Set the recording paper.

3. READY LED (READY)

・

If the magazine is open when recording starts or while recording is being performed,

lights in “orange”.

・

When the magazine is closed,

LED or

lights in “green”.

・

When the recording paper is used up,

LED or

will light in “orange”.

4. Record Key (RECORD)

While the recording is being performed,

LED or

will light in “blue”. Pressing

the key again will stop the recording.

5. Paper Feed Key (FEED)

Even if the recording is not performed, the

LED or

will light in “blue” while

the key is being pressed.

Releasing the key turns off

and stops feeding the paper.

●

Rear Side

6. U-LINK Connector

6. U-LINK Connector

Connects to the main unit.

－

Содержание HR-800







































































Результаты поиска

Содержание HR-800

Отзывы:

Похожие инструкции для HR-800

Бренды по названию

Популярные бренды

Fukuda Denshi HR-800, Руководство по обслуживанию

Результаты поиска

Содержание HR-800

Отзывы:

Похожие инструкции для HR-800

Бренды по названию

Популярные бренды