Fukuda Denshi HR-800 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 70

background image

C A U T I O N

z

Systems

y

Use only the accessories specified for this device. Otherwise, proper

function cannot be executed.

y

For quality improvement, specifications are subject to change without

prior notice.

y

This equipment is intended to be used for only one patient.

y

The installation of this equipment should be performed by our service

representative or a person who is well acquainted with this
equipment.

y

If not using for a long period, make sure to turn OFF the power of the

main unit.

z

Maintenance

y

Clean the device frequently so stains can be removed easily.

y

To prevent injury, it is recommended to wear gloves when cleaning

the equipment.

y

Do not allow liquids or cleaning solution to enter the equipment or

connectors.

y

Do not use organic solvents, thinner, toluene or benzene to avoid

damaging the resin case.

y

Do not polish the housing with abrasive or chemical cleaner.

y

When sterilizing the entire room using a spray solution, pay close

attention not to have liquids get into the monitor or connectors.

y

Use only neutral detergent to clean the housing. Do not use chemical

cloth, scrub brush, abrasive, polishing powder, hot water, volatile
solvent and chemicals (cleanser, thinner, toluene, benzine, benzol,
and synthetic detergent for house and furniture), or sharp-edged
tools. The surface resin coating may be damaged, resulting in
discoloration, scratches, and other problems.

y

Do not open the housing.

y

Avoid alcohol or other liquids from getting into the device.

y

Replace the periodic replacement parts periodically as specified.

Disposing of Equipment, Accessories, or Components

C A U T I O N

When disposing of this product, accessories, or components, use an
industrial waste distributor. Do not dispose of as ordinary waste.

Precautions about Transportation

When transporting HR-800, pack it with specified packing materials.

Reference

Refer to

“

2. Specification

”

for Environmental Conditions during transportation.

vi

«
...
8
9
10
11
12
...
»

Содержание HR-800







































































Отзывы:

Нет отзывов

Похожие инструкции для HR-800

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Relion 615 series

Бренд: ABB Страницы: 136

Бренд: Nelsen Corporation Страницы: 16

Бренд: National Instruments Страницы: 34

Бренд: Jafar Страницы: 10

Бренд: Jafar Страницы: 8

Smart-MPPT Li Series

Бренд: Y-Solar Страницы: 6

Бренд: OJ Electronics Страницы: 8

Бренд: OJ Electronics Страницы: 112

Бренд: OJ Страницы: 17

Бренд: MaintTech Страницы: 28

Бренд: Watlow Страницы: 20

Бренд: A.R.I. Страницы: 14

Бренд: Industrial Controls Страницы: 17

Бренд: SolarEdge Страницы: 20

Dual Motor Focus Controller

Бренд: Pegasus Astro Страницы: 16

Ratio Feeder J+ Advanced Series

Бренд: H.E. Anderson Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды