manualshive.com logo in svg

Fukuda Denshi HR-800, Руководство по обслуживанию

Инструкция по эксплуатации для продукта Ginny's HR-800 доступна для бесплатного скачивания на нашем веб-сайте. Этот подробный руководство поможет вам использовать ваш продукт эффективно и безопасно. Скачайте его сейчас с manualshive.com и наслаждайтесь вашим новым устройством Ginny's HR-800.

Поделиться
Скачать
background image

Cleaning 

This section explains about the cleaning of the housing and cables. 
 

Cleaning the Housing and cables 

Clean the housing using a tightly squeezed gauze or an absorbent cotton cloth dampened with 
alcohol or a neutral cleanser. 
 

C A U T I O N  

z

  Clean the equipment frequently so stains can be removed easily. 

z

  To prevent injury, it is recommended to wear gloves when cleaning the 

equipment. 

z

  Do not allow liquids or cleaning solution to enter the equipment or 

connectors. 

z

  Do not use organic solvents, thinner, toluene and benzene to avoid 

damaging the resin case. 

z

  Do not polish the housing with abrasive or chemical cleaner. 

z

  When sterilizing the entire room using a spray solution, pay close 

attention not to have liquids get into the equipment or connectors. 

z

  Use only neutral detergent to clean the housing. Do not use chemical 

cloth, scrub brush, abrasive, polishing powder, hot water, volatile solvent 
and chemicals (cleanser, thinner, toluene, benzine, benzol, and synthetic 
detergent for house and furniture), or sharp-edged tools. The surface resin 
coating may be damaged, resulting in discoloration, scratches, and other 
problems. 

 
 
 

11

－

10 

Содержание HR-800







































































Отзывы:

Нет отзывов

Похожие инструкции для HR-800

unicore UM960 Installation And Operation User Manual preview
UM960
Бренд: unicore Страницы: 25
unicore UM960L Installation And Operation User Manual preview
UM960L
Бренд: unicore Страницы: 24
Camozzi PRE Series Operation And Maintenance Instructions preview
PRE Series
Бренд: Camozzi Страницы: 33
Camozzi K8 Series Use And Maintenance Instructions preview
K8 Series
Бренд: Camozzi Страницы: 2
Camozzi PME Series Operation & Maintenance Instructions Manual preview
PME Series
Бренд: Camozzi Страницы: 64
WAM LBC Series Assembly And Main Instructions For Use And Maintenance preview
LBC Series
Бренд: WAM Страницы: 62
walimex WR-100 Instruction Manual preview
WR-100
Бренд: walimex Страницы: 7
Walchem WebMaster Manual preview
WebMaster
Бренд: Walchem Страницы: 2
Walchem WebMaster Quick Start Manual preview
WebMaster
Бренд: Walchem Страницы: 73
Walchem W900 Series Instruction Manual preview
W900 Series
Бренд: Walchem Страницы: 126
wallas 3008 Quick Start Manual preview
3008
Бренд: wallas Страницы: 2
Xantrex Trace C35 Installation And Operation Manual preview
Trace C35
Бренд: Xantrex Страницы: 56
Xantrex TrueCharge 2 Owner'S Manual preview
TrueCharge 2
Бренд: Xantrex Страницы: 2
Xantrex Freedom Sequence Owner'S Manual preview
Freedom Sequence
Бренд: Xantrex Страницы: 58
Xantrex Freedom e-GEN Checklist preview
Freedom e-GEN
Бренд: Xantrex Страницы: 4
Xantrex AGS Owner'S Manual preview
AGS
Бренд: Xantrex Страницы: 20
Gardigo 62318 Instruction Manual preview
62318
Бренд: Gardigo Страницы: 6
VAT 244 Series Installation, Operating, & Maintenance Instructions preview
244 Series
Бренд: VAT Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды