Fukuda Denshi HR-800 Скачать руководство пользователя страница 46

Страница: 46 / 70

－

Software Upgrade Procedure

This section describes software upgrade procedure of the HR-800 Recorder Module.

Preparation

・

Connect the HR-800 to the monitor. (For detais of how to connect, refer to the Operation Manual of
the Main Unit.)

・

When the DSC-8500 is connected via the MGU, select MGU in U-LINK Setup for the External Device
Connection.

・

Copy the program file (hr800apl.bin) for the HR-800 installation to a CF Card and insert the CF Card
into a slot on the Main Unit.

Upgrade

・

Press in the following keys: Menu

→

Maintenance

→

Module Install to display the Module Install

screen.

・

Check the current HR-800 version.

・

Check the software version inside the CF Card. To display the version of install file, press the

HR-800 key.

・

Check the version, start the installation by pressing the Start Install key if there is no problem.

・

When the "Install completed" message appears, installation has been completed.

・

The HR-800 automatically restarts and communication to the DSC-8500 series resumes.

Upgrade check

・

Display the Program version screen and check that the version and serial number which were
installed are displayed.

Содержание HR-800







































































Результаты поиска

Содержание HR-800

Отзывы:

Похожие инструкции для HR-800

Бренды по названию

Популярные бренды

Fukuda Denshi HR-800, Руководство по обслуживанию

Результаты поиска

Содержание HR-800

Отзывы:

Похожие инструкции для HR-800

Бренды по названию

Популярные бренды