Fujitsu MHY2040BS страница 84 Скачать руководство пользователя

Страница: 84 / 322

Interface

Primitive Name

Description

R_IP

Reception in progress

Current node (host or device) is receiving
payload.

R_OK

Reception with no error

Current node (host or device) detected no
error in received payload.

R_RDY

Receiver ready

Current node (host or device) is ready to
receive payload.

SOF

Start of frame

Start of a frame. Payload and CRC follow to
EOF.

SYNC Synchronization Synchronizing primitive - always idle.

WTRM

Wait for frame
termination

After transmission of any of the EOF, the
transmitter will transmit WTRM while waiting
for reception status from receiver.

X_RDY

Transmission data ready

Current node (host or device) has payload
ready for transmission.

5.1.3 Electrical specifications

For the electrical requirements of physical layer, refer to "Electrical specifications"
section in the "Serial-ATA Revision 2.5."

5-6

C141-E269

Содержание MHY2040BS



































































































































































































































































































































Результаты поиска

Содержание MHY2040BS

Отзывы:

Похожие инструкции для MHY2040BS

Бренды по названию

Популярные бренды

Fujitsu MHY2040BS, Руководство по эксплуатации/техническому обслуживанию

Результаты поиска

Содержание MHY2040BS

Отзывы:

Похожие инструкции для MHY2040BS

Бренды по названию

Популярные бренды