Fujitsu MHY2040BS страница 112 Скачать руководство пользователя | Manualshive

Страница: 112 / 322

background image

Interface

(3)

WRITE SECTOR(S) (X '30' or X '31')

This command writes data of sectors from the address specified in the
Device/Head, Cylinder High, Cylinder Low, and Sector Number fields to the
address specified in the Sector Count field. Number of sectors can be specified
from 1 to 256 sectors. A sector count of 0 requests 256 sectors. Data transfer
begins at the sector specified in the Sector Number field. For the protocols related
to data transfer, see Subsection 5.4.3.

If the head is not on the track specified by the host, the device performs an implied
seek. After the head reaches to the specified track, the device writes the target
sector.

If an error occurs when writing to the target sector, retries are attempted
irrespectively of the R bit setting.

The data stored in the buffer, and CRC code and ECC bytes are written to the data
field of the corresponding sector(s).

Upon the completion of the command execution, the shadow block registers
contain the cylinder, head, and sector addresses of the last sector written.

If an disk error occurs during multiple sector write operation, the write operation is
terminated at the sector where the error occurred. Shadow block registers contain
the cylinder, the head, the sector addresses (in the CHS mode) or the logical block
address (in the LBA mode) of the sector where the error occurred.

•

Error reporting conditions

(1) A specified address exceeds the range where write operations are allowed

(after a transfer of dummy data, ST = 51h, ER = 10h).

(2) The range where write operations are allowed will be exceeded by an address

during a write operation (after a transfer of dummy data, ST = 51h, ER = 10h).

(3) A write fault was detected when the write cache was disabled

(ST = 71h, ER = 10h).

(4) While the write cache is enabled, if the status indicating a completed transfer

(STS = 50h) is returned and a data write operation failed because a write fault
was detected during the data write operation, Abort will be returned for all
subsequent ATA commands (ST = 71h, ER = 04h). This state is cleared the
next time that the device is turned on.

(5) A SATA communication error occurred (ST = 51h, ER = 14h).

(6) An error other than the above errors occurred (ST = 51h, ER = 04h).

5-34

C141-E269

«
...
110
111
112
113
114
...
»

Содержание MHY2040BS



































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHY2040BS

TotalStorage DS4800

Бренд: IBM Страницы: 250

TotalStorage DS4800

Бренд: IBM Страницы: 234

Бренд: IBM Страницы: 136

System Storage DS5020

Бренд: IBM Страницы: 31

Netfinity EXP300

Бренд: IBM Страницы: 93

Бренд: IBM Страницы: 270

Ultrastar 36LZX

Бренд: IBM Страницы: 2

DCAS-32160 - Ultrastar 2.1 GB Hard Drive

Бренд: IBM Страницы: 232

System Storage TS3310

Бренд: IBM Страницы: 531

Бренд: Accordance Systems Страницы: 58

Бренд: Seagate Страницы: 46

Бренд: Patiowell Страницы: 38

Бренд: Olympus Страницы: 4

Ultrastar 15K73

Бренд: Hitachi Страницы: 273

Travelstar 5K500

Бренд: Hitachi Страницы: 5

Travelstar 5K500.B

Бренд: Hitachi Страницы: 5

Travelstar 40GN

Бренд: Hitachi Страницы: 2

Travelstar 4K40

Бренд: Hitachi Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды