Fujitsu MHY2040BS Скачать руководство пользователя | Manualshive

Страница: 271 / 322

background image

6.1 Reset and Diagnosis

6.1.2.1 Software settings preservation

When a device is enumerated, software will configure the device using SET
FEATURES and other commands. These software settings are often preserved
across software reset but not necessarily across hardware reset. In Parallel ATA,
only commanded hardware resets can occur, thus legacy software only reprograms
settings that are cleared for the particular type of reset it has issued. In Serial ATA,
COMRESET is equivalent to hard reset and a non-commanded COMRESET may
occur if there is an asynchronous loss of signal. Since COMRESET is equivalent
to hardware reset, in the case of an asynchronous loss of signal some software
settings may be lost without legacy software knowledge. In order to avoid losing
important software settings without legacy driver knowledge, the software settings
reservation ensures that the value of important software settings is maintained
across a COMRESET. Software settings preservation may be enabled or disabled
using SET FEATURES with a subcommand code of 06h (refer to Section 5.3.2
(28)). If a device supports software settings preservation, the feature shall be
enabled by default.

6.1.2.2 COMRESET preservation requirements

The software settings that shall be preserved across COMRESET are listed below.
The device is only required to preserve the indicated software setting if it supports
the particular feature/command the setting is associated with.

INITIALIZE DEVICE PARAMETERS

•

•

•

•

•

Device settings established with the INITIALIZE DEVICE PARAMETERS
command.

Power Management Feature Set Standby Timer

The Standby timer used in the Power Management feature set.

Security mode state

The security mode state established by Security Mode feature set commands
(refer to Section 6.13 of the ATA/6 specification). The device shall not
transition to a different security mode state based on a COMRESET. For
example, the device shall not transition from the SEC5: Unlocked / not
Frozen state to state SEC4: Security enabled /Locked when a COMRESET
occurs, instead the device shall remain in the SEC5: Unlocked /not Frozen
state.

SECURITY FREEZE LOCK

The Frozen mode setting established by the SECURITY FREEZE LOCK
command.

SECURITY UNLOCK

The unlock counter that is decremented as part of a failed SECURITY
UNLOCK command attempt.

C141-E269

6-5

«
...
269
270
271
272
273
...
»

Содержание MHY2040BS



































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHY2040BS

Бренд: Bahco Страницы: 4

Бренд: ECKELMANN Страницы: 134

Бренд: Angelbird Страницы: 20

TrueNAS R Series

Бренд: iXsystems Страницы: 24

Бренд: Transcend Страницы: 24

Бренд: Hanover Страницы: 27

TS-h1886XU-RP-R2

Бренд: QNAP Страницы: 62

Бренд: GARANT Страницы: 40

Бренд: oldfields Treco Страницы: 32

Бренд: oldfields Treco Страницы: 28

QuantaGrid D51PH-1ULH

Бренд: QCT Страницы: 167

ST9160511NS - Constellation 7200 160 GB Hard Drive

Бренд: Seagate Страницы: 46

Бренд: Dedicated Micros Страницы: 12

Бренд: Bosch Страницы: 20

Бренд: ETT Страницы: 5

Backup Exec 3600 R3

Бренд: Symantec Страницы: 22

Бренд: GE Intelligent Platforms, Inc. Страницы: 137

Бренд: ABSCO SHEDS Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды