manualshive.com logo in svg

Fujitsu MHY2040BS, Руководство по эксплуатации/техническому обслуживанию

Fujitsu MHY2040BS - надежный жесткий диск для хранения данных. Получите руководство по эксплуатации и обслуживанию бесплатно, загрузив его с manualshive.com. Руководство по эксплуатации доступно для скачивания на русском языке. Узнайте все о своем продукте, чтобы продлить его срок службы и оптимизировать производительность.

Поделиться
Скачать
background image

Interface 

 

5.1.5  P11 function 

The disk drive supports the following functions when P11 pin in the power supply 
segment of interface connector is used as an input or output pin. 

P11 pin supports the functions as follows: 

• 

Staggered Spin-up: 

Use P11 as an input pin 

• 

Driving Activity LED:  

Use P11 as an output pin 

The following is P11 setting and hardware requirement for these functions. 

5.1.5.1  Staggered Spin-up  

It is able to set whether the disk drive spins up at power on or not, by input voltage 
level of 11th pin at the power supply segment on the interface connector. 

a) P11 

→

 Open (no connection): 

Staggered Mode Enable. 

 

The disk drive does not spin up until after 

                                                          successful  Phy initialization at power on.   
                                                          (Default setting) 

b) P11 

→

  Grounded (0.8 V or less):  Staggered Mode Disable. 

                                                         The disk drive spins up at power on. 

c) P11 

→

 "High" level (The P11 line in the host system is pulled up by  

 

resistor [recommended value: 1 to 5.1 k

Ω

] to power supply in the  

 

host system [Recommended voltage: 2V (3.3V or less)]:  

 

 

Staggered Mode Enable 

 

 

The drive does not spin up until after  

 

 

successful Phy initialization at power on. 

5.1.5.2  Driving Activity LED 

It is possible that the disk drive is able to drive P11 pin as output for indication of 
Activity LED. 

a)  P11 output level 

→

  "Low": 

It indicates that the command is in execution. 

 

(LED is on) 

b)  P11 output level 

→

  "High":  It indicates that the command is not  

 

in execution. (LED is off) 

It is necessary to meet the requirements for P11 as output pin in case of driving 
Activity LED. 

5-8 

C141-E269 

Содержание MHY2040BS



































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHY2040BS

LaCie LITTLE BIG DISK THUNDERBOLT 2 Getting Connected preview
LITTLE BIG DISK THUNDERBOLT 2
Бренд: LaCie Страницы: 6
Quantum FIREBALL PLUS AS 10.2 Product Manual preview
FIREBALL PLUS AS 10.2
Бренд: Quantum Страницы: 162
Soyntec HDD Box 250 User Manual preview
HDD Box 250
Бренд: Soyntec Страницы: 8
Tandberg Data STORAGE CAB4000 - Quick Install Manual preview
STORAGE CAB4000 -
Бренд: Tandberg Data Страницы: 13
Galvo Shed GVO3030 Assembly Instructions preview
GVO3030
Бренд: Galvo Shed Страницы: 2
Palram CANOPIA RUBICON How To Assemble preview
CANOPIA RUBICON
Бренд: Palram Страницы: 71
garofalo TUSCANY TERRACE 100.1P User Manual preview
TUSCANY TERRACE 100.1P
Бренд: garofalo Страницы: 16
Watford ELECTRONICS DISC DRIVE Operating Instructions preview
ELECTRONICS DISC DRIVE
Бренд: Watford Страницы: 3
Intenso BUSINESS User Manual preview
BUSINESS
Бренд: Intenso Страницы: 80
The Handy GC-30 Gas Caddy Instructions And Parts List preview
GC-30 Gas Caddy
Бренд: The Handy Страницы: 2
Supermicro SuperServer 110C-FHN4T User Manual preview
SuperServer 110C-FHN4T
Бренд: Supermicro Страницы: 108
Quantum SNC 4500 Release Note preview
SNC 4500
Бренд: Quantum Страницы: 3
LaCie Rikiki Specifications preview
Rikiki
Бренд: LaCie Страницы: 2
LaCie LaCie Little Big Disk 301088 Specification preview
LaCie Little Big Disk 301088
Бренд: LaCie Страницы: 2
LaCie Mini Firewire Companion Hard Drive Quick Start Manual preview
Mini Firewire Companion Hard Drive
Бренд: LaCie Страницы: 22
Kanguru Defender Elite User Manual preview
Defender Elite
Бренд: Kanguru Страницы: 37
X-Micro Bluetooth USB Dongle User Manual preview
Bluetooth USB Dongle
Бренд: X-Micro Страницы: 49
TrekStor SATA-Storage 3.5 Manual preview
SATA-Storage 3.5
Бренд: TrekStor Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды