Fujitsu MHY2040BS Скачать руководство пользователя страница 92

Страница: 92 / 322

Interface

5.2.3 Outline of the frame information structure (FIS)

The transport layer converts data written in a Block Register into the FIS, and
sends it to the upper layer.

The FIS, which is generated in the transport layer, is explained below.

5.2.3.1 FIS types

The types of FIS are as follows (Each FIS is referred to as abbreviation in square
brackets in this manual.):

•

DMA Active – Device to Host [DMA Active]

•

DMA Setup – Device to Host or Host to Device (Bidirectional)
[DMA Setup]

•

Set Device Bits – Device to Host [SetDB]

•

BIST Active – Bidirectional [BIST Active]

•

PIO Setup – Device to Host [PIO Setup]

•

Data – Host to Device or Device to Host (Bidirectional) [DATA]

5-14

C141-E269

Содержание MHY2040BS



































































































































































































































































































































Результаты поиска

Содержание MHY2040BS

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu MHY2040BS, Руководство по эксплуатации/техническому обслуживанию

Результаты поиска

Содержание MHY2040BS

Отзывы:

Бренды по названию

Популярные бренды