Fujitsu MHY2040BS страница 40 Скачать руководство пользователя | Manualshive

Страница: 40 / 322

background image

Device Overview

1.12 Interface Power Management (IPM)

1.12.1 Host-initiated interface power management (HIPM)

When the disk drive is waiting for commands, it can enter one of three IPM modes
as requested by the host. The three IPM modes are:

1) Partial mode: PMREQ_P is sent when the host requests the Partial mode.

2) Slumber mode: PMREQ_S is sent when the host requests the Slumber mode.

3) Active mode: When the serial ATA interface is in active state.

There are three interface (I/F) power states: Active, Partial, and Slumber. As
requested by the host, the disk drive switches its I/F power state from the Active
state to the Partial state, or from the Active state to the Slumber state.

1.12.2 Device-initiated interface power management (DIPM)

If this function is enabled by Set Features command, the disk drive shifts to two
kinds of IPM modes automatically under the Idle condition.

1) Partial mode: PMREQ_P is sent when the disk drive requests the Partial

mode.

2) Slumber mode: PMREQ_S is sent when the disk drive requests the Slumber

mode.

I/F power states

1) Active

state

The SATA interface is active, and data can be sent and received.

2) Partial

state

The SATA interface is in the Power Down state. In this state, the interface is
switched to the Partial state when a PMREQ_P signal is received from or sent
to host. Because the return time to the Active state from the Partial state is
specified as within 10

µ

s, the degree of the I/F Power Save mode is shallow

so that this recovery time is satisfied.

3) Slumber

state

The SATA interface is in the Power Down state. In this state, the interface is
switched to the Slumber state when a PMREQ_S signal is received from or
sent to host. Because the return time to the Active state from the Slumber
state is specified as within 10 ms, the degree of the I/F Power Save mode is
deep so that this recovery time is satisfied.

1-16

C141-E269

«
...
38
39
40
41
42
...
»

Содержание MHY2040BS



































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHY2040BS

Бренд: IBM Страницы: 301

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 8

Taylor-Wharton XL-65

Бренд: Harsco Страницы: 26

G2 R8000 3U WW ERM

Бренд: HPE Страницы: 3

SUPERSERVER 6027TR-H71FRF

Бренд: Supero Страницы: 118

Бренд: Patiowell Страницы: 38

Бренд: Compaq Страницы: 139

Бренд: AIC Страницы: 79

Бренд: SANHO Страницы: 24

Бренд: Netstor Страницы: 11

DataPort 25 Enhanced Carrier

Бренд: CRU Dataport Страницы: 2

Бренд: Westfalia Страницы: 18

Бренд: ramia Страницы: 3

Portable Hard Drive Combo USB

Бренд: Verbatim Страницы: 31

Pro 2-Disk RAID USB and eSATA

Бренд: Verbatim Страницы: 56

Бренд: Alpha ESS Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды