Fujitsu MHY2040BS Скачать руководство пользователя | Manualshive

Страница: 174 / 322

background image

Interface

(21) READ DMA (X 'C8' or X 'C9')

The host system can select the DMA transfer mode by using the SET FEATURES
command, however, the transfer speed does not change.

•

Ultra DMA transfer mode 0 to 5

(1) A specified address exceeds the range where read operations are allowed

(ST = 51h, ER = 10h).

The READ DMA command reads data from sectors, starting from the sectors
specified in the Device/Head, Cylinder High, Cylinder Low, and Sector Number
fields and continuing for as many sectors as specified in the Sector Count field. A
value ranging from 1 to 256 can be specified for the number of sectors. In order to
specify 256, "00" must be set in the Sector Count field. For the protocol
concerning data transfers, see Section 5.4.4.

When the command is completed, either cylinder, head, and sector addresses
(CHS mode) or the logical block address (LBA mode) of the last sector is stored in
the Shadow Block Register.

If an error such as an uncorrectable disk read error is detected during execution of
the READ DMA command and continued operation not possible, the data transfer
stops after all data, including the data of the sector where the error was detected, is
transferred. The device notifies the host of the status by sending the RegDH FIS.
At this time, the number of remaining sectors including the sector where the error
was detected, and either cylinder, head, and sector addresses (CHS mode) or the
logical block address (LBA mode) of the sector where the error was detected are
stored in the Shadow Block Register.

•

Multiword DMA transfer mode 0 to 2

•

Error reporting conditions

(2) The range where read operations are allowed will be exceeded by an address

during a read operation (ST = 51h, ER = 10h).

(3) An uncorrectable disk read error occurred (ST = 51h, ER = 40h).

(4) The sync byte indicating the beginning of a sector was not found

(ST = 51h, ER = 01h).

(5) A SATA communication error occurred (ST = 51h, ER = 0Ch).

(6) A Host Buffer CRC error occurred (ST = 51h, ER = 84h).

(7) An error other than the above errors occurred (ST = 51h, ER = 04h).

5-96

C141-E269

«
...
172
173
174
175
176
...
»

Содержание MHY2040BS



































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHY2040BS

StorageLoader DLT VS160

Бренд: Tandberg Data Страницы: 13

StorageLoader DLT VS160

Бренд: Tandberg Data Страницы: 46

StorageLibrary LTO-3 SCSI

Бренд: Tandberg Data Страницы: 2

SDLT220-320 INTEGRATION

Бренд: Tandberg Data Страницы: 142

Бренд: Tandberg Data Страницы: 3

Бренд: Tandberg Data Страницы: 12

Бренд: Gardebruk Страницы: 32

Бренд: Secure Data Страницы: 2

OCEAN SIDE 8435059720210

Бренд: Naterial Страницы: 28

Бренд: IBM Страницы: 68

Бренд: AIC Страницы: 88

Бренд: Seagate Страницы: 36

Бренд: Bosch Страницы: 76

GTA 2500 Compact Professional

Бренд: Bosch Страницы: 84

Бренд: Sun Microsystems Страницы: 118

Бренд: QNAP Страницы: 55

Бренд: ABSCO SHEDS Страницы: 25

MediaShare Wireless SD/USB device

Бренд: Verbatim Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды