Fujitsu MHY2040BS Скачать руководство пользователя | Manualshive

Страница: 38 / 322

background image

Device Overview

•

Power Mode shifted with APM or APS feature.

•

SLUMBER signal transferred
(PMREQ_S signal is transferred from the host or the drive, and the host
responds with PMACK signal.)

Emergency Unload other than Unload is performed when the power is shut down
while the heads are still loaded on the disk.
The product supports the Emergency Unload a minimum of 20,000 times.
When the power is shut down, the controlled Unload cannot be executed.
Therefore, the number of Emergency other than Unload is specified.

1.10.1 Recommended power-off sequence

We recommend cutting the power supply of the HDD for this device after the
Head Unload operation completes. The recommended power supply cutting
sequence for this device is as follows:

1) Disk

Flush

Flush Cache command execution.

2) Head

Unload

Standby Immediate command execution.

3) Wait

Status

Checking whether bit 7 of the status register was set to '0'.
(wait to complete STANDBY IMMEDIATE command)

4) HDD power supply cutting

1.11 Advanced Power Management (APM)

The disk drive automatically shifts to the power saving mode according to the
setting of the APM mode under the idle condition.

The APM mode can be chosen with a Sector Count register of the SET
FEATURES (EF) command.

The disk drive complies with the three kinds of APM modes that a command from
the host is required.

FR = 05h : Enable APM

SC = C0h - FEh : Mode-0 Active Idle

→

Low Power Idle

SC = 80h - BFh :

Mode-1 Active Idle

→

Low Power Idle (Default)

SC = 01h - 7Fh :

Mode-2 Active Idle

→

Low Power Idle

FR = 85h : Disable APM (Set Mode-0)

Active Idle:

The head is in a position of extreme inner in disk

1-14

C141-E269

«
...
36
37
38
39
40
...
»

Содержание MHY2040BS



































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHY2040BS

HD080HJ - 80 GB Hard Drive

Бренд: Samsung Страницы: 2

G2 PORTABLE HX-MU025DC

Бренд: Samsung Страницы: 36

DSN-3200 - xStack Storage Area Network Array Hard...

Бренд: D-Link Страницы: 7

Бренд: Data General Страницы: 58

Azure StorSimple 8100

Бренд: Microsoft Страницы: 12

05DTMBAX0307DD-V1

Бренд: Mercia Garden Products Страницы: 9

Бренд: morse Страницы: 6

Бренд: ST Страницы: 9

Бренд: Suncast Страницы: 28

Бренд: AIC Страницы: 79

InTANK iR2775-S3

Бренд: Raidon Страницы: 2

Бренд: CalDigit Страницы: 16

Бренд: VIKA Страницы: 12

Бренд: Roland Страницы: 2

G-SPEED SHUTTLE

Бренд: G-Technology Страницы: 8

Бренд: G-Technology Страницы: 27

Бренд: G-Technology Страницы: 38

Бренд: G-Technology Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды