FujiFilm SD1125S2 Скачать руководство пользователя страница 55

Страница: 55 / 68

PART III INSPECTION AND SERVICE

2．INSPECTION, CLEANING, AND CHANGE OF OIL

●

For inspection and service, place the machine on a flat and large space without obstacle.
Stop the engine and make sure each part has stopped its operation completely and heating
part has cooled down before inspection and service.

●

During inspection and service, never smoke or keep anything which may cause fire near
the machine. Otherwise, the fuel ignites and fire may occur.

●

Do not supply fuel or oil in excess of the prescribed amount. Wipe away any spilled fuel
or oil completely.

●

If the covers are detached, be sure to fix them to their original position.

●

When inspecting or changing oil, keep the machine in horizontal position.

●

When changing oil, use receptacle for oil. Do not spill the oil around the machine. If the oil spilled,
wipe it off completely.

●

Be sure to dispose of waste oil in a place with waste oil disposal facilities.

■INSPECTION AND CHANGE OF ENGINE OIL

▼

Inspection　→　Carry out before every work

●

Refer to page 26 of this manual.

▼

Change　→　Refer to "Engine manual".

(1)

Detach filler cap and drain plug. Drain the oil.

(2)

Attach the drain plug and put prescribed oil
through the filler port.

(3)

Check with an oil gauge that the oil level is
between the two marking lines on the gauge.

(4)

Attach the filler cap.

●

Check the amount of oil again when
more than 5 minutes have passed after
replenishing the oil.

●

Refer to "Engine manual" for
details of time and method of changing.

■INSPECTION, CLEANING, REPLACEMENT OF
AIR CLEANER

▼Inspection → Before every work

●

Refer to page 26 of this manual.

▼Cleaning, replacement → Refer to "Engine manual"

SDS1-02-01

SDS1-02-02

●

Refer to "Engine manual" for details
of time and method of replacement.

■INSPECTION OF HST OIL TANK

▼Inspection → Before every work

●

Refer to page 26 of this manual.

02-8619-11

Oil to use

Engine oil for diesel

10W-30 CD class or higher

In case using the machine out of the

temperature range above, refer to

"Engine manual".

1.55　L

Amount

Oil to use

Engine oil for gasoline

10W-30 SE class or higher

（－15℃ to 15℃）

HST oil tank

Knob Air cleaner cover

Air cleaner base

Element

Gromme

Urethane

foam

Regular range

Upper limit

Lower limit

WARNING

CAUTION

DANGER

SUPPLEMENT

- 50 -

Содержание SD1125S2





































































Результаты поиска

Содержание SD1125S2

Отзывы:

Похожие инструкции для SD1125S2

Бренды по названию

Популярные бренды

FujiFilm SD1125S2, Руководство по эксплуатации

Результаты поиска

Содержание SD1125S2

Отзывы:

Похожие инструкции для SD1125S2

Бренды по названию

Популярные бренды