9 - 5
Digit
17
18
19
20
21
22
23
<Measuring range> 4th component
Minimum range
Maximum range
None None
0 to 50ppm
0 to 1000ppm
0 to 100ppm
0 to 2000ppm
0 to 200ppm
0 to 500ppm
0 to 200ppm
0 to 2000ppm
0 to 200ppm
0 to 5000ppm
0 to 500ppm
0 to 1%
0 to 1000ppm
0 to 2%
0 to 5000ppm
0 to 10%
0 to 1%
0 to 20%
0 to 2%
0 to 50%
0 to 10%
0 to 20%
0 to 10%
0 to 100%
<O
2
analyzer, 1st range>
Minimum range
Maximum range
None None
0 to 5%
0 to 25%
0 to 10%
0 to 25%
Other
<Output>
4 to 20mA DC
0 to 1V DC
4 to 20mA DC + Communication function
0 to 1V DC + Communication function
<O
2
conversion and O
2
average value output>
None
With O
2
conversion output
With peak alarm
With O
2
conversion output and peak alarm
<Adjustment, Range designation>
For combustion exhaust gas (specified range)
For combustion exhaust gas
For combustion exhaust gas (specified range)
Unit mg/m
3
For combustion exhaust gas, Unit mg/m
3
Others
Description
note 4
note 4
note 6
note 7
note 8a)
note 8a)b)
note 8b)
note 9
Y
L
M
Z
A
B
C
D
B
E
F
G
Z
Y
A
B
C
C
C
E
F
H
J
K
M
M
4 5 6 7
1 2 3
Z K J F
6
8
9 10 11 12 13
14 15 16 17 18 19 20
Y
F
G
E
G
H
J
K
M
N
P
N
R
Y
V
V
Z
Y
A
B
C
21 22 23
Digit No.
of code
Note 1
a) When “B” is specified at the 6th digit, O
2
sensor signal has to be set as 0-1V DC linear corresponding to full scale.
b) External Zirconia O
2
sensor and external O
2
analyzer are not included in the scope of supply, and has to be separately
ordered.
Note 2
Resin coupling with purging cannot be manufactued.
Note 3
Rated voltage, plug type and applicable standard of the attached power cord is different depending on the code “J”, ”E”,
”U” and “C” in the 10th digit.
Select appropriate cord according to operating power supply voltage in the final destination.
Note 4
Measuring range can be selected within either the minimum or maximum range.
(Within min. or max. range, you can change the actual range settings locally.)
Initial setting from Fuji factory is Min. range for the 1st range, and Max. range for the 2nd range.
When range preset at Fuji factory is required, please select “specified range” at 23rd digit and inform Fuji of specified
range
table.
Refer to Section 9.3 (1) - (8), for possible combination of measuring components and ranges in the data sheet.
Note 5
“1E” can be specified at 11th & 12th digits, ONLY for CO
2
measurement.
In this case, be sure to select “with purging” at 7th digit.
Note 6
O
2
conversion is calculated only for NO, SO
2
and CO.
Both average value output after O
2
calculation and O
2
average value output are provided at the same time.
a) Peak count alarm can be added only for CO measurement.
Note 7
When “Y” is specified at the 6th digit, 22nd digit always has to be specified as “Y”.
Note 8
a) If you would like Fuji to deliver ZKJ analyzer with specific range setting, select “specified range” and separately inform
Fuji of the actual range of each component together with your purchase order.
b) In case that the measurement unit is specified as “mg/m3”, it is necessary to select “unit : mg/m
3
” (Code “F” or “G”)
at the 23rd digit.
Please refer to the table shown below for the corresponding range code based on “mg/m
3
”.
note
Note 9
When “Z” is specified at the 23rd digit, a gas composition table of actual measued gas has to be sent to Fuji
together with your purchase order.
Note 10
When only N
2
O analyzer is used, make sure not to contain any components other than N
2
O .
Multicomponent analyzers including N
2
O an CO
2
analyzer are used for sludge incineration.
In this case, the range of N
2
O is 0 to 200ppm/500ppm, and the range of CO
2
is 0 to 10%/20%.
Min. range Max. range Min. range Max. range Min. range Max. range Min. range Max. range
AF
0-50ppm
0-1000ppm
BG
0-100ppm 0-2000ppm
CH
0-200ppm 0-5000ppm
0-70mg/m
3
0-140mg/m
3
0-280mg/m
3
0-1300mg/m
3
0-2600mg/m
3
0-6600mg/m
3
0-150mg/m
3
0-300mg/m
3
0-600mg/m
3
0-2800mg/m
3
0-5500mg/m
3
0-14g/m
3
0-65mg/m
3
0-130mg/m
3
0-250mg/m
3
0-1250mg/m
3
0-2500mg/m
3
0-6250mg/m
3
Corresponding range in mg/m
3
or g/m
3
Range code
In ppm
NO
SO
2
CO
