manualshive.com logo in svg

Fronius LaserHybrid MHP 360i LH, Руководство по эксплуатации

Поделиться
Скачать
Fronius LaserHybrid MHP 360i LH Скачать руководство пользователя страница 86

86

Inserting the La-
ser Optics

IMPORTANT!

 When replacing the laser optics, ensure that the laser optics and welding 

torch are compatible in terms of the focal length.

Remove 2 x springs from the removed 
laser optics and insert into the new la-
ser optics

IMPORTANT!

 When inserting the new la-

ser optics, ensure that the installation posi-
tion is correct:
-

The plug on the fiber optic cable, coo-
lant hoses and protective glass drawer 
must all be accessible,

-

the push-button must be up.

Insert the laser optics so that the 
springs are underneath in the grooves

Press the laser optics at the rear end 
down
Move the laser optics into the holder 
and into the guide

Insert 4 x Allen screws
Tighten the Allen screws slightly
size 4 mm

1

2

2

CAUTION! 

Dropping the laser op-

tics may lead to damage beyond 
repair.
Insert and handle the laser optics 
carefully.

1

2

4

3

4

4

3

4

5

6

5

5

5

5

6

Содержание LaserHybrid MHP 360i LH

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды