manualshive.com logo in svg

Fronius LaserHybrid MHP 360i LH, Руководство по эксплуатации

Поделиться
Скачать
Fronius LaserHybrid MHP 360i LH Скачать руководство пользователя страница 22

22

Requirements

Mechanical Re-
quirements

The following mechanical requirements must be met in order to ensure a stable and re-
peatable LaserHybrid process:
-

Accurate welding torch guidance for robots or single-purpose machines (e.g. longitu-
dinal chassis)

-

Precise weld seam preparation

-

Low component tolerances

-

Precise and very fast weld seam management systems with little deviation

Robot Require-
ments

The laser welding head weighs around 19 kg. The optics weigh a further 3 kg approximate-
ly. A total weight of around 30 kg should be expected for the complete laser welding head 
when fitted with optics and hosepack.
It must therefore be possible for the robot axles to move a weight of 30 kg safely with the 
accelerations specified.

IMPORTANT! 

The maximum permitted acceleration for the laser welding head is 3 g at 5–

150 Hz, based on use of the laser optics.

Ground Connec-
tion

Grounding cable with bifilar winding

Grounding cable coiled

-

-

Содержание LaserHybrid MHP 360i LH

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды