Fronius LaserHybrid MHP 360i LH Скачать руководство пользователя

Страница: 82 / 112

Remove 2 x register pins:

Position and connect extractor
tool for register pins

Hit the vibrating mass on the ext-
ractor tool backward and then re-
move the register pins

Remove bracket for robot connection

Position the laser welding head so that the longitudinal axis on the laser welding head
is outside of the horizontal (> 90°)
Shut off the hose for the extra extraction

IMPORTANT!

Only shut off the coolant

hose on the laser optics, never on the fiber
optic cable.

Loosen the Allen screw and shut off
the coolant hose from the laser optics
size 2.5 mm

To shut off the fiber optic cable from the laser optics, reverse the sequence used for con-
nection; see page 53, work step 6 onward:

Clean the fiber optic cable and connection area with compressed air
Pull rubber sleeve back in direction of optics

Press button underneath

Disconnect fiber optic cable

Fit protective covers on fiber optic cable plug and fiber optic cable connection

Содержание LaserHybrid MHP 360i LH

















































































































Результаты поиска

Содержание LaserHybrid MHP 360i LH

Отзывы:

Похожие инструкции для LaserHybrid MHP 360i LH

Бренды по названию

Популярные бренды

Fronius LaserHybrid MHP 360i LH, Руководство по эксплуатации

Результаты поиска

Содержание LaserHybrid MHP 360i LH

Отзывы:

Похожие инструкции для LaserHybrid MHP 360i LH

Бренды по названию

Популярные бренды