manualshive.com logo in svg

Fronius LaserHybrid MHP 360i LH, Руководство по эксплуатации

Поделиться
Скачать
Fronius LaserHybrid MHP 360i LH Скачать руководство пользователя страница 65

65

EN-US

(5)

Scale for additional adjustment option on the z-axis

Adjustment range 0 / +10  mm

Basic position for the Trumpf optics holder = 0

Loosen the 2 x Allen screws size 5 mm in order to make additional adjustments on 
the z-axis and move the optics holder.
Tightening torque for the Allen screws = 10 Nm

(6)

Adjusting screw with division for z-axis

Adjustment range +12 / -7 mm
Allen screw size 5 mm
¼ turn equates to adjustment travel of 0.25 mm
Reading accuracy using Nonius 0.1 mm

Setting Up X-Axis

Loosen 2 x Allen screws size 5 mm (1)

Set up the x-axis using the adjusting 
screw and Allen key size 5 mm:
1 x turn equates to 1.0 mm

After setting up the x-axis, re-tighten the 2 x Allen screws size 5 mm (1)

NOTE! 

The x-axis and y-axis are set up with the cover removed from the drive 

unit.
Re-fit the cover on the drive unit after set-up.

(1)

(1)

1

1

1

2

2

2

3

Содержание LaserHybrid MHP 360i LH

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды