manualshive.com logo in svg

Franklin Fueling Systems TS-LS500, Руководство по установке

Поделиться
Скачать
Franklin Fueling Systems TS-LS500 Скачать руководство пользователя страница 3

Contents

Introduction ......................................................................................................................................1

Definitions and acronyms ..............................................................................................................1
Applications ...................................................................................................................................2
Site Requirements ..........................................................................................................................2

Minimum pressure requirements ..............................................................................................2
Pipe length to hold minimum line volume  ................................................................................2
Pipe length to hold maximum line volume ................................................................................2
Maximum and minimum line volume for rigid and flexible pipe...............................................2

TS-LSU500 dimensions ..................................................................................................................3
Transducer Installation ..................................................................................................................3

Intrinsically Safe Installation .............................................................................................................4
Explosion Proof TS-LS500E Installation ............................................................................................6
TS-LS500 Setup (Console Programming) ..........................................................................................8

AC Input Module .........................................................................................................................8

4-20mA Input Module ...................................................................................................................10
Relay Module .................................................................................................................................10
Turbine Pump Interface (TPI) Applications ....................................................................................12
Fuel Management Systems (FMS) Line Application Set-Up ..........................................................13

Line Status and Control Screens .......................................................................................................15

TS-LS500 Status Screen ..................................................................................................................15
TS-LS500 Control Screen ................................................................................................................17

Control Section ...........................................................................................................................17
Learn Section ..............................................................................................................................17

Pre-Operational TS-LS500 Testing ....................................................................................................18

Required Equipment ......................................................................................................................18
Purging the line ..............................................................................................................................19

Zero Offset ..................................................................................................................................19

Line Stability Test ...........................................................................................................................20

Learn Process ....................................................................................................................................21

When to learn or re-learn ..............................................................................................................21
Procedure .......................................................................................................................................22
Learn Messages .............................................................................................................................23

TS-LS500 Reports ..............................................................................................................................24

TS-LS500 Line Leak Reports ...........................................................................................................24

Alarms ...............................................................................................................................................25

TS-LS500 Alarms and Warnings .....................................................................................................26
Clearing Alarms ..............................................................................................................................29

Содержание TS-LS500









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды