manualshive.com logo in svg

Franklin Fueling Systems TS-LS500, Руководство по установке

Поделиться
Скачать
Franklin Fueling Systems TS-LS500 Скачать руководство пользователя страница 29

25

Alarms

When a T5, EVO

TM

 600, or EVO

TM

 6000 console is in alarm, the Alarm LED on the front of the 

console will flash. If the line has been programmed to shut down the pump on failed test (in the 
FMS Setup), the pump will be unavailable for all system tests and dispensing until the line with 
the active alarm is manually reset. If the condition still exists after reset, the alarm will return. A 
service visit may be required to identify and correct the condition. 

 

WARNING: 

Always REMOVE POWER from the console prior to installing/removing a module 

or performing any maintenance while the console door is open.

NOTE:

  Refer to the Important Safety Messages outlined in the beginning of this manual before 

performing any console maintenance. 

NOTE:

  If this guide is not able to help you correct a Warning or Alarm, please contact FFS 

Technical Services (1-800-984-6266).

Содержание TS-LS500









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды