manualshive.com logo in svg

Franklin Fueling Systems TS-LS500, Руководство по установке

Поделиться
Скачать
Franklin Fueling Systems TS-LS500 Скачать руководство пользователя страница 7

3

TS-LSU500 dimensions

6.25"

(159 mm)

5.13"

(130 mm)

2" NPT

3/4" NPT

2-3/8" (70mm) 

across flats

Transducer Installation

1.  Lock out tag out and relieve line pressure using Manual Pressure Relief.
2.  Remove two-inch pipe plug or older leak detector from submersible pump or adaptor tee.
3.  Examine straight bore for corrosion, if rough smooth with emery paper.
4.  Apply UL Classified Gasoline/Oil resistant pipe thread sealant to the threads of the 

transducer and use a 2 3/8”  open-end wrench to install it in the Leak Detector Port of the 
STP housing (see Figure 1).

NOTE:

 

When using TS-LS500 line leak detection in a manifolded line application, you only need 

to use one transducer to monitor the entire line. This transducer should be located in the master 
STP. In-line check valves should NOT be used as the line leak detection will not be able to test 
beyond them. Please see the STP manufacture about appropriate check and/or relief valves. 

5.  Install Couplings, threaded Rigid Metal Conduit (RMC), and Explosion/Weather Proof 

Junction Boxes (J-Boxes) in the STP sump. For intrinsically safe wiring, run the transducer 
lead to the junction box. For explosion-proof installations, run conduit to the top of the 
transducer.

6.  Install threaded RMC and EYS fittings along with Transducer Cables (Belden #9365) from TS-

LS500 console to the Explosion/Weather Proof J-Boxes. A licensed electrician should splice 
the cables together. If this wiring is Intrinsically Safe it MUST NOT be run with any Explosion-
Proof wiring or other non-Intrinsically safe wiring! Alpha cable #58411 must be used if using 
nonmetallic (PVC) conduit as allowed by local code.

Содержание TS-LS500









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды