manualshive.com logo in svg

Franklin Fueling Systems TS-LS500, Руководство по установке

Поделиться
Скачать
Franklin Fueling Systems TS-LS500 Скачать руководство пользователя страница 10

6

Explosion Proof TS-LS500E 
Installation

NOTE:

 The Explosion Proof 4-20mA Input Module has a RED face. 

 

WARNING: 

Lockout and tag circuit breakers, and disconnect console power wiring before 

installing or servicing any system wiring.

 

WARNING: 

DO NOT make transducer wiring connections with power connected to the 

console or any module.

 

CAUTION:

 Do not run intrinsically safe (IS) wiring and non-intrinsically safe (non-IS) wiring in 

the same conduit.

NOTE:

 TS-LS500E must be installed in accordance with the national electrical code, ANSI/NFPA 

70, CEC or other applicable national or local codes.

NOTE:

 The explosion-proof transducer needs to have explosion-proof conduit to the head of the 

transducer.

1.  Pull the wiring through the explosion proof conduit that will be used for the TS-LSU500E 

transducer. 

2.  Mount the TS-LSU500E in the pump manifold. 
3.  The TS-LSU500E wiring must enter the console in Explosion Proof conduit through a knockout 

on the Hazardous side of the barrier. Secure each pair of transducer wires to a single channel 
on the 4-20mA Input Module. Always start at the first available channel and do not skip 
channels. For example, if channels one through three are already being used for another 
application channel 4 must be used. Be sure to connect the wires to the correct polarity (+/-). 
If the transducer is wired backwards it will not function.

Содержание TS-LS500









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды