Force FORCEOL115-E, Инструкция по установке, эксплуатации и обслуживанию

Страница: 15 / 68

15
106346-06 - 8/19
FORCE
Installation, Operating & Service Manual
Step 2. Thread 1-1/4" x 1-1/4" x 3/4" NPT
tee on opposite end of 5" lg. nipple
installed in Step a.
NOTE:
Based on access for servicing
and location of sewer or floor drain,
when tightening these fittings,
determine if drain valve is to be located
on the left or right side.
Tighten nipple and tee into 1-1/4" NPT
lower rear tapping on rear section
until joints are water tight for desired
position.
Boiler Model
Baffle Usage
2
nd
Pass 3
rd
Pass
Combustion
Chamber
FORCEOL084-E
[2]
P/N 102066-01
None None
FORCEOL115-E
[2]
P/N 109902-01
[2]
P/N 100081-01
[1]
P/N 109901-01
FORCEOL140-E
[2]
P/N 100042-01
None None
FORCEOL182-E
Table 3: Baffle Usage
Step 3. Apply sealant to 3/4" NPT thread
on drain valve. Thread into 3/4" NPT
tapping on side outlet of tee. Use hex
nut portion to tighten valve until water
tight.
5. Connect Field Wiring.
Connect the field wiring from the circulator to
the HydroStat 3250 control. Make the wiring
connections as shown on Figures 27 and 28.
6. Installing stainless steel flueway baffles. Baffle
requirements differ from model to model, see
Table 3.
NOTE:
Read caution statement
before
proceeding.
CAUTION
These baffles will generate higher efficiencies
and lower stack temperatures. Under certain
conditions, a lower gross stack temperature
entering the chimney has the potential to
be cooled below the dew point and create
condensate on interior surfaces. Flue gas
condensate is corrosive, which requires
special consideration and must be addressed
immediately.
DO NOT install baffles until you have read
Sections VI and VII, completely (venting
details).
Install stainless steel baffles provided in
miscellaneous parts carton as follows, refer to
Table 3 and Figure 9:
•
FORCEOL084E
- To install flueway baffle
in 2
nd
pass on left side of boiler, hold
baffle with word "Left" readable at the
top. Slide baffle in flueway until position
tab touches fins on left side of 2
nd
pass
flueway. To install flueway baffle in 2
nd
pass flueway on right side of boiler, hold
baffle with word "Right" readable at the
top. Slide baffle in flueway until position
tab touches fins on right side of 2
nd
pass flueway.
• Model EMP115E - To install flueway
baffle in 3
rd
pass on left side of boiler,
hold baffle with the word "Left" readable
at the top. Slide baffle in flueway until
position tab touches fins on left side
of 3
rd
pass flueway. To install flueway
baffle in 3
rd
pass flueway on right side
of boiler, hold baffle with word "Right"
readable at the top. Slide baffle in
flueway until position tab touches fin on
right side of 3
rd
pass flueway. To install
flueway baffle in 2
nd
pass on left side
of boiler, hold baffle with word "Left"
readable from the top. Slide baffle in
flueway until position tb touches fins on
left side of 3
rd
pass flueway. To install
flueway baffle in 2
nd
pass flueway on
right side of boiler, hold baffle with word
"Right" readable at the top. Slide baffle
in flueway until position tab touches fins
on right side of 3
rd
pass flueway.
To install combustion chamber Ring,
set ring in the front section of the
combustion chamber.
•
FORCEOL140-E
and
FORCEOL182-E
To
install flueway baffle in 2
nd
pass flueway
on left side of boiler, hold baffle with
word "Left" readable at the top. Slide
baffle in flueway until position tab
touches fins on right side of 2
nd
pass
flueway. To install flueway baffle in 2
nd
pass flueway on right side of boiler, hold
baffle with word "Right" readable at the
top. Slide baffle in flueway until position
tab touches fins on left side of 2
nd
pass
flueway.
NOTE: 2
nd
and 3
rd
pass flueway baffle are not
interchangeable.
!
3
Packaged Boiler Assembly - Trim & Controls
(continued)