manualshive.com logo in svg

FOR-A USF-212PS, Руководство по эксплуатации, Страница: 26 / 40

Поделиться
Скачать
FOR-A USF-212PS Скачать руководство пользователя страница 26

26 

  Status 

 

Model names of the modules installed in slots 1 to 12 of USF-212S are displayed. 
PS1 and PS2 indicate the respective power supply mounting and operational states. 
A red flashing LED indicates abnormal power output, inoperative fan, or a high temperature 
state being detected. 

 

  Unit Information 

Serial No. 

Serial number 

Version 

Version information 

 

  Power Unit 1 Status / Power Unit 2 Status (*) 

DC Output 

DC output status of the Power Unit is indicated. 
Normal:  Functioning 
Abnormal:  Not functioning.  Immediately turn off the power supply and 
contact your supplier. 

Fan 

Operation status of Power Unit FAN is indicated. 
Normal:  Functioning 
Stopped:  The fan has stopped.  Immediately turn off the power supply 
and contact your supplier. 

* Not indicated when the power is turned on for a power supply that is not installed. 

 

  Front Fan Status 

Fan 1 to 3 

Status of front FAN 1 to FAN 3.  Refer to Sec. 4-1 

"Front Panel” for 

FAN location. 
Normal:  Functioning 
Stopped:  The fan has Stopped.  Immediately turn off the power supply 
and contact your supplier. 

 

  Genlock Status 

Genlock 1 

Detected:  Input signal is detected. 
Loss:  Input signal is not detected. 

Genlock 2 

Detected:  Genlock 2 input signal is detected. 
Loss:  Input signal is not detected. 

 
 

Содержание USF-212PS









































Отзывы:

Нет отзывов