Fluke CableAnalyzer DSX-5000 Скачать руководство пользователя страница 653

Страница: 653 / 700

Chapter 21: Specifications

DSX Series Module Specifications

617

HDTDR Analyzer Specifications for Cables <100 m (328 ft)

Characteristic Impedance

The tester gives an estimate of the cable's impedance at 4 m from
the start of the link. The accuracy of the measurement is relative
to a 100



terminating resistance.

Tone Generator

Generates tones that can be detected by a tone probe, such as a
Fluke Networks IntelliTone

™

probe. The tones are on all pairs. The

tone generator does not generate the IntelliTone signal.

The tone generator also turns on an inactive main or remote DSX
CableAnalyzer connected to the other end of the cable.

Input Protection

Protected against continuous telco voltages and 100 mA over-
current. Occasional ISDN over-voltages will not cause damage.

Parameter

Twisted Pair Cabling

Distance accuracy



(0.3 m (1 ft) + 2 % distance)

Distance resolution

0.1 m or 1 ft

Parameter

Twisted Pair Cabling

Range



- 180



Accuracy

± (5



+ 5 % of



100



– Measured



)

Resolution



Содержание CableAnalyzer DSX-5000





























































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CableAnalyzer DSX-5000

Отзывы:

Fluke CableAnalyzer DSX-5000, Техническое справочное руководство, Страница: 653 / 700

Результаты поиска

Содержание CableAnalyzer DSX-5000

Отзывы: