Fluke CableAnalyzer DSX-5000 Скачать руководство пользователя страница 223 | Manualshive

Страница: 223 / 700

Fluke CableAnalyzer DSX-5000 Скачать руководство пользователя страница 223

Chapter 6: Diagnose Copper Test Failures

Causes of Twisted Pair Test Failures

187

When the FAULT INFO Tab Does Not Show

To provide fault information, the tester needs TDR, crosstalk, and
other results to do frequency and time domain analysis. For the
settings and cables listed below, the

FAULT INFO

tab does not

show because the tester cannot get the measurements it needs:



The

HDTDR/HDTDX

setting on the

TEST SETUP

screen is set to

Never

.



The

Cable Type

is set to Cat 3, Class F, Class F

A

, or Class II.



The link has only 2 pairs.



The link has a wire map failure.

For the cables listed above, if you set

HDTDR/HDTDX

on the

TEST

SETUP

screen to

Fail/Pass* only

, you can use the HDTDR and

HDTDX analyzers to help you identify and locate faults. See “The
HDTDR Analyzer” on page 194 and “The HDTDX Analyzer” on
page 200.

Causes of Twisted Pair Test Failures

Table 8. Causes of Twisted Pair Test Failures

Wire Map test fails

Open



Wires connected to wrong pins at connector or punchdown blocks



Bad connection



Damaged connector or cable



Wrong application for the cable or the wrong outlet configuration is
selected

Short



Damaged connector or cable



Conductive material stuck between pins at connector



Incorrect termination at a connector



Wrong application for the cable

«
...
221
222
223
224
225
...
»

Содержание CableAnalyzer DSX-5000





























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов