Fluke CableAnalyzer DSX-5000 Скачать руководство пользователя страница 313 | Manualshive

Страница: 313 / 700

Fluke CableAnalyzer DSX-5000 Скачать руководство пользователя страница 313

Chapter 9: Certify Fiber Cabling

Autotest in Loopback Mode

277



Maximum loss for multimode TRCs

: 0.15 dB



Maximum loss for singlemode TRCs

: 0.25 dB

If the tester shows a warning, clean and inspect the
connectors on the TRC, make sure the cords do not have
tight bends, as shown in Figure 117, then do the TRC
verification again.

Step 3: Do an Autotest in Loopback Mode

W

Caution

If you disconnected the test reference cord from the
output of the tester, you must set the reference
again to make sure your measurements are reliable.

3-1

On the

SET REFERENCE

screen, when the set reference or

TRC verification procedure is completed, tap

NEXT

to see

how to connect to the fiber under test.

3-2

Clean and inspect the connectors on the fiber under test.

3-3

Make the connections to do the test on the fiber, as shown on
the screen and in Figure 117, then press

HOME

.

3-4

Tap

TEST

on the main tester or press



on the main or

remote tester.

If the

CHECK FIBER CONNECTIONS

screen shows an open

fiber:



Make sure that all connections are good and no fibers
have damage. Use the VFL to make sure the fiber under
test has continuity.

-continued-

«
...
311
312
313
314
315
...
»

Содержание CableAnalyzer DSX-5000





























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов